Can the Prodigy P2 # 90885 Be Mounted at a Steep Angle of 75 to 80 Degrees

Question

Question:

Can the Prodigy P 2 controller be mounted at a steep angle on the dash 75 to 80 degrees?

asked by: Robert Z

0

Expert Reply:

Yes the Prodigy P2 Brake Controller, # 90885, can mount at a steep angle of 75 to 80 degrees. The P2 can be mounted from 0 degrees to 360 degrees vertically in the direction of travel. The front of the P2 must be level from side to side and it must be parallel with the direction of travel.

Check out the diagram that I attached showing how the P2 must be mounted. I pulled this diagram from the installation instructions that I have attached as well.

expert reply by: John H

0

click to enlarge

Answer 1

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 2

The Prodigy P3 part #90195 will work for you because your trailer has electric brakes. The P3 can install and work just fine on vehicles with air brakes. The only thing it needs from the vehicle is access to a circuit that only sees voltage when the…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 6

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 7

Hey Ron, congratulations on the new trailer! I have a Jay Feather myself and love it. You're definitely off to a great start with a weight distribution hitch, it will make a world of difference towing that trailer with your F-150. The Weigh Safe…

view full answer...

Answer 8

Hey David, we can help with a brake controller install in your 2006 Jeep Wrangler that has a factory 7-way but your Jeep does not have brake controller pre-wiring so you would need to hardwire in the controller with a kit like the part #5506 and a…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Can the Prodigy P2 # 90885 Be Mounted at a Steep Angle of 75 to 80 Degrees

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching