Dimensions of TRU37FR Replacement E-Z Lube Spindle

Question

Question:

Hello, Im wondering if you have a dimensional drawing of this TRU37FR spindle? Thanks

asked by: Austin C

0

Expert Reply:

If you take a look at the provided photo, you can see the pertinent dimensions of the # TRU37FR spindle.

expert reply by: Mike L

0

click to enlarge

Answer 1

If you take a look at the provided photo, you can see the important dimensions of the #TRU37FR spindle.

view full answer...

Answer 2

The most common bearings and seals for a 7,000 pound axle are #25580 inner bearing, #14125A outer bearing, #25520 inner race and #14276 outer race. The grease seal can vary, and will usually either be the #GS-2250DL, which has a 2.250 inch inner…

view full answer...

Answer 3

The Spindle #TRU37FR is going to be welded in place on your torsion axle. It will most likely need to be cut off and torched out due to the way your axle is clocked near the mounting bracket. Before you attempt to replace the spindle be sure to check…

view full answer...

Answer 4

Trailer spindles are welded directly to the axle so to remove one it just needs to be cut off completely using a torch or saw. Then to replace the spindle such as with the EZ Lube #TRU37FR that you were looking at it's extremely important that it…

view full answer...

Answer 5

First, thanks for all that detailed information, it was very helpful. And we can get you parts for your trailer, though the issue is that there isn't an available hub for your spindle due to what you mentioned - the uncommon 501349 bearing, which…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Dimensions of TRU37FR Replacement E-Z Lube Spindle

Product Page this Question was Asked From

Continue Researching