Replacement Landing Gear Motor Part # 1-065-041012-01

Question

Question:

I have a 2007 Keystone Everest 345s with the landing gear motor part# 1-065-041012-01 with a 9000rpm speed. What would the replacement motor for this one be? I don’t find a replacement model # with a 9000rpm speed. Thanks.

asked by: Jim M

0

Expert Reply:

I've reached out to Lippert about your specific question and the motor you need is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893.

expert reply by: Adam E

0

click to enlarge

Answer 1

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 2

I reached out to my contact at Lippert and since your landing gear motor is blowing a fuse as soon as it sees load he mentioned the issue is more than likely that the motor is not getting the correct voltage, with the less common cause being the…

view full answer...

Answer 3

Yes, according to Lippert the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 would be a compatible replacement for your 1-065-041012-01 motor.

view full answer...

Answer 4

Finding continuity to ground on the running light circuit of your trailer indicates that the circuit has a short to the frame of the trailer most likely and is your problem. What you'll need to do is trace the circuit starting at the assemblies…

view full answer...

Answer 5

The landing gear motor we carry that has a 7,140 RPM rating is part #LC141893. It has a 5,000 pound capacity as well. I've linked a video for you.

view full answer...

Answer 6

I'm not sure what you're using now, Bill, but the LED Porch Light for RVs #DG52526PB is what I'd recommend going with. Diamond Group has a pretty good track record as being reliable and long lasting, but I can't say that it'll…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Landing Gear Motor Part # 1-065-041012-01

Product Page this Question was Asked From

Continue Researching