Replacement Motor for Lippert Model 1-065-041012-01 Landing Gear

Question

Question:

on my fifth wheel, I have a Lippert Model 1-065-041012-01 12 V DC motor, for raise the two jacks. Will your LG-196308 be an equivalent or better replacement? Will it bolt right up without modifications? Thanks!

asked by: Steve D

0

Expert Reply:

The correct replacement for your 1-065-041012-01 motor is part # LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson # LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll want the replacement motor to match the output of the original.

I've linked you to a product description video for the replacement motor.

expert reply by: Mike L

0

Perry

5/18/2024

Yes but it has a 30% higher torque output

Reply

Kurt F.

8/26/2024

@Perry Hi Perry. My 1-065-041012-01 landing gear motor, yes its 7140 RPM. My problem is it will blow 3 or 4 30amp fuses to lift it. I need something with more torque. What should I get?

Reply

Jon G.

8/26/2024

@KurtF We don't have something with a higher torque, but I do wonder if you might be possibly overloading your landing gear? Landing gear might struggle some at higher capacities, but it shouldn't be blowing fuses if you're within the limits of your system and all of your wiring connections are in good condition.

Reply

Answer 1

I reached out to my contact at Lippert and since your landing gear motor is blowing a fuse as soon as it sees load he mentioned the issue is more than likely that the motor is not getting the correct voltage, with the less common cause being the…

view full answer...

Answer 2

From what I could find on your Apollo Halftime AAC34BIB microwave/convection oven, it needs cut-out measurements of 21-3/4" wide x 16-5/8" tall x 19-1/4" deep. We do not have a microwave that will perfectly fit those measurements. The…

view full answer...

Answer 3

Trailer wheels that are 14.5 inches in diameter are hard to find as half sizes like this are not common at all. The overall diameter of the tire size 7-14.5 is 27.7 inches. The most similar diameter trailer tire size is the 205/75-15 which has a…

view full answer...

Answer 4

Hey Johnny, thanks for reaching out! I highly recommend using the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 as a replacement for your 8532-07 motor. According to my research your motor is rated for 5,500 lbs so this motor will…

view full answer...

Answer 5

The 125340 motor that you currently have on your 2008 Montana Mountaineer 35 foot 5th Wheel is equivalent to the Replacement Motor #LG-142178. This is compatible with the Replacement Aluminum Gearbox #LG-179015 which is also what you want to use for…

view full answer...

Answer 6

If the bevel gears/gearbox for the dual-motor landing gear on your 2011 Keystone Laredo 266RL 5th wheel were badly worn or damaged you would most likely be able to hear it. These conditions typically cause a good bit of noise as the jacks try to…

view full answer...

Answer 7

We do have a few 12 volt ceiling fan options, but they all use a wall switch and not a remote. We do not have a remote version available. The ceiling fans do come with a few different color options, listed below. Brushed Nickel - White - 12V RV…

view full answer...

Answer 8

Yes, the the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893 will absolutely work to replace the Atwood 71113 motor on your fifth wheel. Motors are very much interchangeable so the fact that one was on a camper and yours…

view full answer...

Answer 9

For the gearbox on your 2008 Forrest River Sandpiper I recommend the Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear Assemblies #LC276602. The aluminum casing is far more sturdy than the plastic housing options. If you…

view full answer...

Answer 10

The part number 125340 you referenced is actually a motor, and the correct replacement for that is Replacement Motor #LG-142178. However, since you mentioned gears in the gearbox, you will need to replace the entire thing, which for your landing gear…

view full answer...

Answer 11

Hi James, The 15-1/2" distance between weld stops is standard, so you can use whichever legs give you the right amount of height and lift. For a set that has a retracted height of 32-3/4" and extended height of 53-1/4" with…

view full answer...

Answer 12

The best way to tell if it is a motor issue or a gear box is to use the manual crank. If it is the motor, the landing gear will function perfectly with the manual crank. If it is the gear box, then you will have a very similar issue with the…

view full answer...

Replacement Motor for Lippert Model 1-065-041012-01 Landing Gear

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching