Replacement For A 1-065-041012-01 Landing Gear Motor

Question

Question:

Customer has a 2011 Primetime Crusader motor #1-065-041012-01 and needs a replacement does the LC141893 work for replacement

asked by: Jessica C

0

Expert Reply:

Yes, according to Lippert the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 would be a compatible replacement for your 1-065-041012-01 motor.

expert reply by: Kevin C

0

Answer 1

I reached out to my contact at Lippert and since your landing gear motor is blowing a fuse as soon as it sees load he mentioned the issue is more than likely that the motor is not getting the correct voltage, with the less common cause being the…

view full answer...

Answer 2

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 3

I've reached out to Lippert about your specific question and the motor you need is the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor #LC141893.

view full answer...

Answer 4

Finding continuity to ground on the running light circuit of your trailer indicates that the circuit has a short to the frame of the trailer most likely and is your problem. What you'll need to do is trace the circuit starting at the assemblies…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement For A 1-065-041012-01 Landing Gear Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching