Recommended Trailer Hitch Receiver for 2021 Toyota RAV4 XLE

Question

Question:

I looking a hitch for Rav4 XLE 2021,you dont haved. IS THE SAME FOR 2020 AND 2021?

asked by: Raymi O

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # DT82QR is compatible with the 2021 Toyota RAV4 models. It will work well for your XLE trim as well. I've attached a video of the installation on a 2020 model which will be the same on the 2021 XLE.

expert reply by: Jason S

0

Answer 1

The Draw-Tite Max-Frame Trailer Hitch Receiver part #DT82QR and Curt Trailer Hitch Receiver part #C13416 are both fits for a 2020 Toyota RAV4 and install in the exact same manner. I recommend the Curt Trailer Hitch Receiver simply for the fact that…

view full answer...

Answer 2

Hey Corey, I finally got my hands on both the Curt #C33NR and Draw-Tite #DT82QR and was able to measure from the mounting holes down to the bottom of the receiver tube to see which had more ground clearance. The Draw-Tite #DT82QR had a 12.5"…

view full answer...

Answer 3

I appreciate that you only one to know one thing, and the answer to which trailer hitch has the most ground clearance for a 2020 Toyota RAV4 is ... (dramatic pause) ... the Draw-Tite Trailer Hitch #DT82QR. The margin was very, very close though,…

view full answer...

Answer 4

When we installed the Draw-Tite Class III Trailer Hitch #DT82QR and the Curt Class III #C13416 on the 2019 model Toyota RAV4, we actually measured an identical ground clearance measurement of 12". This is taken from the ground to the top of the…

view full answer...

Answer 5

If you check out the attached install instruction link on this page for the Draw Tite hitch part #DT82QR you can see several pictures of it installed. I attached a single picture to this page that shows it installed for you to check out. The bend in…

view full answer...

Answer 6

If you are looking at the Curt Hitch #C66KR and the Draw-Tite Hitch #36675, both of these 1-1/4 inch hitches have ground clearances of 12 inches. Ground clearance is measured from the ground to the bottom of the upper part of the receiver tube…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hey Adrian! The higher capacity for the B&W #BW47BR and Curt #C77MJ comes from the construction. The B&W hitch weighs 45 lbs and then the Curt and Trailer Mate #TMT54FR both weigh 32 lbs. The Trailer Mate does sit just a tad higher compared…

view full answer...

Answer 12

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Recommended Trailer Hitch Receiver for 2021 Toyota RAV4 XLE

Featured Help Information

Miscellaneous Media

Continue Researching