How To Install Replacement Tail Clamp Assembly for Extang Solid Fold

Question

Question:

How can old broken clamp be removed and new clamp installed on soft trifold 2.0 I have tried removing old one and cannot? This is clamp closest to cab of truck not rear of truck.

asked by: Kirk

1

Helpful Expert Reply:

In order to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers part # EX1035 you'll simply remove the hinge cap, slide the old clamp off, slide the new clamp on, then reinstalled the hinge cap. I have attached a photo to assist.

expert reply by: Conner L

1

click to enlarge

Answer 1

How to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers #EX1035 depends on what cover you have. The replacement tail clamp fits the Extang Solid Fold, Solid Fold 2.0, and Trifecta covers. The Solid Fold…

view full answer...

Answer 2

I'm glad to hear that you received the Rear Tailgate Clamp, #EX31003005, for your Extang Trifecta 2.0 tonneau cover. I called Extang and discovered that they don't have any videos for replacing the rear clamp. But, they were kind enough to…

view full answer...

Answer 3

The Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers #EX1035 and front clamp #EX42FJ have a very basic design of a bolt with a nut on the end. You will remove the hinge cap or latch pocket cover from the cover and simply slide out…

view full answer...

Answer 4

When it comes to towing components like hitches, you're always going to be limited to the capacity of your lowest rated components; so adding a higher rated hitch to your vehicle isn't going to increase your towing capacity or the payload.…

view full answer...

Answer 5

Hey Craig, thanks for reaching out! You'll need to cut part of the rail to remove the old and install the new Replacement Tail Clamp Assembly #EX1035. It seems kind of goofy to me, but my contact at Extang confirmed this is how the installation…

view full answer...

Answer 6

Yes, the part #EX1035 is the correct replacement tail clamp assembly for an Extang Solid Fold tonneau cover like what you have. I attached install instructions for this clamp for you to check out as well.

view full answer...

Answer 7

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 8

If you have the Extang Solid Fold or Solid Fold 2.0 Tonneau Cover, it sounds like you are just needing the Replacement Tail Clamp Assembly #EX1035. This includes 1 complete tail clamp assembly and will be a direct replacement for a tail clamp on your…

view full answer...

Answer 9

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold 2.0 Hard Tonneau Cover like #EX83651 you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need…

view full answer...

Answer 10

I was not able to find the installation instructions for the Replacement Tail Clamp Assembly, part #EX1035, but I did find the instructions for the Extang Solid Fold Tonneau Cover part #EX83700. I have attached those instructions and you can see…

view full answer...

Answer 11

I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How To Install Replacement Tail Clamp Assembly for Extang Solid Fold

Product Page this Question was Asked From

Continue Researching