Replacement Tail Clamp Assembly Recommendation for Extang Solid Fold Tonneau Cover

Question

Question:

I have an Extang Solid Fold 56450 6.5 foot bed I have to replace both tail clamp assemblies. Will part number EX1035 work for that cover? Thanks

asked by: KAREN H

0

Expert Reply:

Yes, the part # EX1035 is the correct replacement tail clamp assembly for an Extang Solid Fold tonneau cover like what you have.

I attached install instructions for this clamp for you to check out as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 2

The Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers #EX1035 and front clamp #EX42FJ have a very basic design of a bolt with a nut on the end. You will remove the hinge cap or latch pocket cover from the cover and simply slide out…

view full answer...

Answer 3

To identify the correct clamp downs for your Extang cover we need to know the model and serial number off the cover as there are different clamps depending on what cover you have and when it was made. For example the Replacement Tail Clamp Assembly…

view full answer...

Answer 4

Hey Craig, thanks for reaching out! You'll need to cut part of the rail to remove the old and install the new Replacement Tail Clamp Assembly #EX1035. It seems kind of goofy to me, but my contact at Extang confirmed this is how the installation…

view full answer...

Answer 5

I'm glad to hear that you received the Rear Tailgate Clamp, #EX31003005, for your Extang Trifecta 2.0 tonneau cover. I called Extang and discovered that they don't have any videos for replacing the rear clamp. But, they were kind enough to…

view full answer...

Answer 6

How to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers #EX1035 depends on what cover you have. The replacement tail clamp fits the Extang Solid Fold, Solid Fold 2.0, and Trifecta covers. The Solid Fold…

view full answer...

Answer 7

I spoke with my contact at Extang and they send me a set of install instructions that cover the installation and removal of the rear section of the Extang Solid Fold 2.0 which I attached to this page.

view full answer...

Answer 8

I was not able to find the installation instructions for the Replacement Tail Clamp Assembly, part #EX1035, but I did find the instructions for the Extang Solid Fold Tonneau Cover part #EX83700. I have attached those instructions and you can see…

view full answer...

Answer 9

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold 2.0 Hard Tonneau Cover like #EX83651 you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need…

view full answer...

Answer 10

In order to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers part #EX1035 you'll simply remove the hinge cap, slide the old clamp off, slide the new clamp on, then reinstalled the hinge cap. I have…

view full answer...

Answer 11

If you have the Extang Solid Fold or Solid Fold 2.0 Tonneau Cover, it sounds like you are just needing the Replacement Tail Clamp Assembly #EX1035. This includes 1 complete tail clamp assembly and will be a direct replacement for a tail clamp on your…

view full answer...

Answer 12

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Replacement Tail Clamp Assembly Recommendation for Extang Solid Fold Tonneau Cover

Product Page this Question was Asked From

Continue Researching