Bearing Kit for Spindle that Has Bearing Diameter of 1.06 inch and Seal Dimension of 1.5 inch

Question

Question:

Need trailer wheel bearing kit 1 1/16 axle 2 outside 1 1/2 seal.

asked by: Paul M

0

Expert Reply:

Based on your seal dimension being 1.5 inch and your bearing dimension of 1.06 inch on your spindle the correct bearing kit you need is the part # BK1-150.

expert reply by: Jameson C

0

Answer 1

Yes, the Dexter Single Axle Heavy Duty Suspension Kit part #K71-403-00 will work on tandem axle trailer you'll just need to purchase multiple kits. This is a standard kit that will work great for most trailers but if you're looking for an…

view full answer...

Answer 2

Based on the pictures you attached and the outer bearing measurement you provided, it appears that you have 1-1/16 inch spindle like the BTR EZ Lube Spindle #TRU44FR. This particular spindle is designed for 2,000 pound axles and will use the same…

view full answer...

Answer 3

The Dexter Single Axle Heavy Duty Suspension Kit #K71-403-00 uses the Shackle Bolt #007-126-01. The 9/16" portion of this bolt is 2-1/4" long.

view full answer...

Answer 4

Hey Eric, the Dexter part #K71-358-00 is a really great option for a heavy duty shackle kit for a single axle trailer like your 2025 Coachmen 12000ROK. The shackles are 1/2 inch thick. I didn't believe this at one point and went out and measured…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Bearing Kit for Spindle that Has Bearing Diameter of 1.06 inch and Seal Dimension of 1.5 inch

Product Page this Question was Asked From

Continue Researching