Solera Power Awning Idler Head Attachment Screw Size

Question

Question:

What size/type is the Phillips screw that attaches the Idler Head to the support arm? Attached is screw on Power Head side.

asked by: Curt A

0

Expert Reply:

The screw size for the attachment screw on a Solera Power Awning Idler Head # LC672052, is a 5/16"-18 x 2-1/4" Phillips head screw. You can pick this up at your local hardware store.

expert reply by: John R

0

Answer 1

Hey David, welcome back! The SeeLeveL II RV Holding Tank Monitor item #SE74RR has momentary switches on the tank selection and battery buttons. However, the water pump switch is an alternate-action toggle, rather than momentary. It sounds like you…

view full answer...

Answer 2

Hey Tony, we have the High Pointe Microwave part #HP84ZR that would fit the cut out you have as it measures 22-5/16" wide x 15-1/8" tall x 14-1/2" deep. But do you need a front vent setup for it or am I misunderstanding you?

view full answer...

Answer 3

I attached a picture of what the wax screws look like for the Solera awnings like of the #LC289561 instructions that you referenced. Basically it's under the black cap that you'll pop off and you'll unscrew that you see in the second…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 9

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

If you are referring to the head pin then yes we do have this available as the Replacement Head Pin for Solera Power Awning Gear Drive Head part #LC266141. That said, you would also want two Replacement Retaining Clips part #LC266137 and one…

view full answer...

Answer 12

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Solera Power Awning Idler Head Attachment Screw Size

Continue Researching