Cover for Ironhorse 2 Motorcycle Trailer

Question

Question:

I am looking for a cover for my Ironhorse trailer. The dimensions are: Total Length with tongue-15 Feet, 4 Inches Body Length-12 feet, 4 inches Width-8 feet, 4 inches Height-6 feet, 7 inches Do you have any covers that would fit this?

asked by: Robert H

0

Expert Reply:

The Adco SFS AquaShed Cover # 290-46003 might fit your Ironhorse Flip Top 2 Bike/1 Trike Trailer if you're planning on using it for short-term storage, but it's not a confirmed official fit. The dimensions sound right so it might work with a bit of creativity and some extra straps.

Your trailer has these dimensions:
148" Long
100" Wide
79" Tall

While the Adco SFS AquaShed Cover # 290-46003 has these dimensions:

168" Long
104" Wide (at base)
80" Wide (at top)
94" Tall

If you can verify that your Ironhorse trailer will fit within the 80" wide measurement at the top, then you're within the dimensions of the Aquashed cover. If you want to cover your tongue as well, you can consider getting the 16' version # 290-46004 which has similar height and width measurements but is two feet longer.

The Aquashed cover comes with three buckle straps that go across the bottom as you can see in the attached video. Those will tighten the edges together and weigh down the cover so it doesn't fly off. If you still want a better fit especially with this cover being about a foot and a half too long, you can pick up extra straps like # E98876-4 to really cinch it in.

The AquaShed Cover is a great cover made of high quality material that will protect your trailer from the rain, snow, and sun. It works so much better than a tarp thrown over your trailer. You won't be able to flip off the top with this cover on, but it does have a rear panel in the back so you might be able to access your rear door. However you decide to cover your trailer, I recommend picking up a dehumidifier like # CAM44195 to keep it fresh while you store it.

expert reply by: Evangeline M

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

Hey Rob, congrats on the new SUV. To add a hitch to your 2026 Honda Pilot, I recommend the etrailer item #e27KR. This hitch is custom fit for your Pilot and comes with all hardware necessary for installation. The etrailer item #e27KR is a class III…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

Hello Hoan, thanks for reaching out. I double checked with the manufacturer, and they confirmed that yes, the etrailer Class 3 Hitch #e27KR will indeed fit the 2025 Honda Pilot Elite. It will be a no drill install and you will not need to cut any of…

view full answer...

Cover for Ironhorse 2 Motorcycle Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching