Bike Racks Loose Fit in Receiver Fixed with Anti-Rattle Device
Updated 09/22/2020 | Published 09/18/2020
Products Featured in This Question
Question:
The 1 1/4" bike rack fits loosely into the receiver of this hitch and uses a locking pin through the hole. It seems sturdy but it is not a tight fit. Is that OK?
asked by: Sherwin
Expert Reply:
The tolerances between a bike rack and hitch are not very close and frequently causes rattle in transit. As long as the rack is inserted fully, and a hitch pin with clip installed, you need not to worry about the bike rack coming off. However if your rack and bikes wobble a lot this could eventually cause damage to the rack or the bikes. There are solutions for this issue.
I would check your bike rack and see if it has an anti-rattle device built into it. It usually looks like a large twist knob, or possibly just a bolt head that you can tighten. If you provide tell me what model of bike rack you have I could determine if it has an anti-rattle device built in, or provide a specific solution.
If you would just like a generic solution I would recommend the Curt # F-315 Anti-Rattle Kit.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches: The Breakdown
- Shop: Trailer Hitch Anti-Rattle Kit for 1-1/4" Trailer Hitches
- Shop: Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Video: Comprehensive Review: Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories
- Q&A: How to Stabilize Bike Rack That is Loose in Hitch
- Q&A: Thule Bike Rack Compatibility With Factory Hitch With Less Than 1.5 Inches From Pin Hole To End
- Search Results: anti~rattle hitch lock hitch anti~rattle
- Search Results: threaded pin trailer hitch lock
- Search Results: suspension enhancement
- Search Results: threaded pin style hitch anti~rattle
- Search Results: fits 2 inch hitch hitch anti~rattle
- Video: Ultimate Overview of the Curt Trailer Hitch Receiver Adapter
- Video: Curt Hollow Shank Accessories Anti-Rattle Kit Review
- Video: An In-Depth Look at the Curt Trailer Hitch Receiver Adapter
- Video: Review of etrailer Hitch Anti-Rattle - Anti-Rattle - e38FV
- Shop: B&W Anti-Rattle Clamp for 2" Hitch Receivers
- Shop: Gen-Y Anti-Rattle Clamp for 2-1/2" Hitch Receivers
- Shop: Advantage Threaded Trailer Hitch Receiver Lock for 1-1/4" Hitches
- Shop: Curt Trailer Hitch Receiver Adapter - 1-1/4" (Class II) to 2" - 6" Long
- Shop: BTBRV Magnetic Hitch Receiver Reducer Set - 3" to 2-1/2" & 2-1/2" to 2"
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Shop: Base Plate for Tow Bar
- Shop: Roof Rack
- Shop: Camper Tie-Downs
on Trailer Hitch
