Recommendation 1-1/4 Inch Drawbar with 3-1/2 Inch Rise on 2015 Nissan Altima
Published 08/31/2020
Products Featured in This Question
Question:
I have a Curt Trailer Hitch, product # C11352, on my 2015 Nissan Altima. I want to tow a light trailer for my kayak. What drawbar would you recommend? I need a rise of approximately 3.5 inches. If in the drawbar information, it states, Class II, will that work with my hitch, which is Class l? Thanks P. S. I currently use the hitch for a Thule bike rack. I doubt that info matters, but included it anyway.
asked by: Gary P
Expert Reply:
We have a 3-3/4 inch rise that works great with your trailer, item # C45023 . It's the Curt Class I Drawbar - 3-3/4" Rise - 11-1/2" Long - 2,000 lbs drawbar.
It is slightly taller than your desired rise. But once the trailer is hooked up, the weight will bring it down closer to that 3.5 inch you were looking for. Also, this drawbar is a Class I which suits your hitch. We have a review video for this product that I've included.
You could use a Class II drawbar with your Class I hitch since it is a Curt. Still, I recommend going for the drawbar above, item # C45023 , as it more closely aligns with your needs.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Let’s Check Out the Draw-Tite Drawbar for 1-1/4" Hitches
- Shop: Trailer Hitch
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 11-3/4" Long - 3,500 lbs
- Shop: Curt Hitch Extension and Reducer for 2-1/2" Trailer Hitches - 24" to 34" Long
- Shop: Trailer Hitch Extender for 1-1/4" Trailer Hitch Receivers - 7" Long
- Shop: Curt Hitch Extender for 2" Hitch Receivers - 8" Long
- Shop: Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Search Results: trailer hitch
- Video: How to Choose a Trailer Brake Controller
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Video: Clean Up Your Trailer Wiring
- Search Results: trailer hitch ball mount
on Trailer Hitch
Gary P.
8/31/2020
I have a Curt Trailer Hitch, product # C11352, on my 2015 Nissan Altima. I want to tow a light trailer for my kayak. What drawbar would you recommend? I need a rise of approximately 3.5 inches. If in the drawbar information, it states, Class II, will that work with my hitch, which is Class l? Thanks P. S. I currently use the hitch for a Thule bike rack. I doubt that info matters, but included it anyway.