Powered Bulldog Jack Recommendation for a 2011 Dodge Ram 1500 to Help Install Spring Bars of WD

Question

Question:

I have a 28foot camper, approx. 6500 lbs. dry weight. I pull it with a 2011 Dodge Ram 1500 4X4. I use weight distribution bars, and what I want to know is will the Bulldogs 4000 lb. unit lift the camper and truck so I can hook up the weight distribution bars?? Thank you for any help,

asked by: Darrin S

0

Expert Reply:

The Bulldog Powered-Drive Trailer Jack # BD500200 would do well as a powered jack for your 6500 lb trailer. It would also work to jack up your trailer to install the weight distribution system you have.

This jack can lift trailers with up to 4,000 lbs of tongue weight. Typically the tongue weight of a trailer is 10-15% of the total weight of the trailer. So when your trailer is empty you would have a tongue weight of 650-975 lbs which the # BD500185 would make easy work of.

expert reply by: Jameson C

0

Answer 1

Sounds like the inner screw of the Bulldog Powered Trailer Jack part #BD500200 that you have is damaged which would require the jack to be replaced. If it's less than 5 years you might be able to get it warrantied but otherwise you'd need to…

view full answer...

Answer 2

I have a solution for you, but the Bulldog #BD500200 is only going to be about 2" shorter than you current jack, and I think we can do a little bit better than that to make sure that you get full use of the tailgate on your 2019 Chevy Suburban.…

view full answer...

Answer 3

The inner leg of the Bulldog Powered Drive Trailer Jack #BD500200 that you referenced is a solid tube. It does not have a welded seam that runs up the leg of the jack.

view full answer...

Answer 4

I had our warehouse measure the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White #BD500200 and it measures at 4-1/4" wide as shown in the included diagram. I included a video of the #BD500200 for you to…

view full answer...

Answer 5

For your Bulldog Electric camper jack #BD500200 will run just fine off of any 12V battery. Often the trailers that use these jacks will have other components they will run as well like lighting, vent fans, etc so it is recommended to use a deep cycle…

view full answer...

Answer 6

The Bulldog Powered-Drive Trailer Jack, item #BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make…

view full answer...

Answer 7

If your 4K Bulldog A-Frame jack like part #BD500199 or #BD500200 is struggling under the tongue weight of a 14,000 lb trailer then I would have to agree that it likely isn't getting the power it needs from the 7-Way on your truck and using a…

view full answer...

Answer 8

The retracted height of the Bulldog Powered-Drive 4,000 Pound Capacity Trailer Jack, #BD500200, is 9-3/4 inches, measured from the bottom of the foot up to the bottom of the bracket that mounts to the trailer frame. I have included a link to a video…

view full answer...

Answer 9

To determine if this powered drive trailer jack will fit on your existing trailer and current set up you will need to measure from the center of the current mounting jack rearward. The Bulldog powered drive trailer jack that you referenced needs at…

view full answer...

Answer 10

The specifications we have for the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs #BD500199 (Black) and #BD500200 (White) are the correct ones. We take these measurements ourselves and the 31-3/4" extended…

view full answer...

Answer 11

The Bulldog Powered Drive a-frame trailer jack #BD500200 is circuit protected internally so additional fuses or breakers are not required. The jack should be ran off of a trailer mounted battery and not off of the 12 volt circuit through the trailer…

view full answer...

Answer 12

The distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, #BD500200, is 13 inches.

view full answer...

Powered Bulldog Jack Recommendation for a 2011 Dodge Ram 1500 to Help Install Spring Bars of WD

Featured Help Information

Miscellaneous Media

Continue Researching