Shaft diameter on the Bulldog Powered-Drive Camper Jack # BD500200

Question

Question:

What is the shaft diameter for this product? I assume it is standard size which is for 2 1/4 hole in the camper A frame. Is the bolt pattern also standard? Thanks.

asked by: Garry

0

Expert Reply:

The Diameter of the main tube is 2-1/4 inches on the Bulldog Powered-Drive Camper Jack, item # BD500200. There are 6 holes in the mounting plate for either 2-1/2 inch mounting pattern or 3 inch mounting pattern. These are the standard bolt patterns used by most trailer manufacturers.

expert reply by: Robert G

0

Answer 1

To determine if this powered drive trailer jack will fit on your existing trailer and current set up you will need to measure from the center of the current mounting jack rearward. The Bulldog powered drive trailer jack that you referenced needs at…

view full answer...

Answer 2

The specifications we have for the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs #BD500199 (Black) and #BD500200 (White) are the correct ones. We take these measurements ourselves and the 31-3/4" extended…

view full answer...

Answer 3

From the center of the shaft to the front outside edge of the motor housing is 3-1/2 inches. I included some of the mounting plate when I measured for height, which is 8-1/4 inches, since that sticks out over the shaft as well. I also measured from…

view full answer...

Answer 4

The Bulldog Powered-Drive Trailer Jack, item #BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make…

view full answer...

Answer 5

If your 4K Bulldog A-Frame jack like part #BD500199 or #BD500200 is struggling under the tongue weight of a 14,000 lb trailer then I would have to agree that it likely isn't getting the power it needs from the 7-Way on your truck and using a…

view full answer...

Answer 6

The distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, #BD500200, is 13 inches.

view full answer...

Answer 7

The inner leg of the Bulldog Powered Drive Trailer Jack #BD500200 that you referenced is a solid tube. It does not have a welded seam that runs up the leg of the jack.

view full answer...

Answer 8

The Bulldog Powered-Drive Trailer Jack #BD500200 would do well as a powered jack for your 6500 lb trailer. It would also work to jack up your trailer to install the weight distribution system you have. This jack can lift trailers with up to 4,000 lbs…

view full answer...

Answer 9

For your Bulldog Electric camper jack #BD500200 will run just fine off of any 12V battery. Often the trailers that use these jacks will have other components they will run as well like lighting, vent fans, etc so it is recommended to use a deep cycle…

view full answer...

Answer 10

Sounds like the inner screw of the Bulldog Powered Trailer Jack part #BD500200 that you have is damaged which would require the jack to be replaced. If it's less than 5 years you might be able to get it warrantied but otherwise you'd need to…

view full answer...

Answer 11

The retracted height of the Bulldog Powered-Drive 4,000 Pound Capacity Trailer Jack, #BD500200, is 9-3/4 inches, measured from the bottom of the foot up to the bottom of the bracket that mounts to the trailer frame. I have included a link to a video…

view full answer...

Answer 12

I have a solution for you, but the Bulldog #BD500200 is only going to be about 2" shorter than you current jack, and I think we can do a little bit better than that to make sure that you get full use of the tailgate on your 2019 Chevy Suburban.…

view full answer...

Shaft diameter on the Bulldog Powered-Drive Camper Jack # BD500200

Continue Researching