Width Of Head On Bulldog Powered Drive Trailer Jack BD500200

Question

Question:

What is the width of the motor head of the 500200? I see where you provide the width 4.5 for a 500185 but I do not know if it would be the same as a 500200. Thank you.

asked by: Bob M

0

Expert Reply:

I had our warehouse measure the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 22" Lift - 4,000 lbs - White # BD500200 and it measures at 4-1/4" wide as shown in the included diagram.

I included a video of the # BD500200 for you to take a look at.

expert reply by: Samuel C

0

Width Of Head On Bulldog Powered Drive Trailer Jack # BD500200
(click to enlarge)

Answer 1

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 2

Yes, you can use the Bulldog Powered Drive Trailer Jack #BD500199 in place of your existing jack because the mounting hole pattern in the bracket will be the same between the 2 jacks. Provided that your existing jack also has a round outer tube that…

view full answer...

Answer 3

There is a Bulldog jack that has numerous bolt holes to allow you to unbolt the jack and rotate it 90 degrees, the Bulldog Powered Drive Trailer Jack #BD500199. You can see an example of this in the linked video - just forward to about the 6:15 mark.…

view full answer...

Answer 4

I have a complete replacement jack option for you, but the buttons on your Lippert Smart Jack #LC643589 are not replaceable so the only option is a complete replacement. If your jack is still within the 1-year warranty period then I recommend…

view full answer...

Answer 5

There is no reason why you could not turn the jack at a 90 degree angle to gain more clearance. Due to the configuration of the holes in the mounting flange, you might need to drill new holes in your trailer tongue to mount the jack in that…

view full answer...

Answer 6

Sounds like the inner screw of the Bulldog Powered Trailer Jack part #BD500200 that you have is damaged which would require the jack to be replaced. If it's less than 5 years you might be able to get it warrantied but otherwise you'd need to…

view full answer...

Answer 7

The Bulldog Powered-Drive Trailer Jack, item #BD500200, only has one wire, the power wire. This jack attaches to ground through the mounting hardware and the trailer frame. When wiring the jack to your 7-Way trailer connector you will need to make…

view full answer...

Answer 8

The distance from the top of the mounting plate to the bottom of the housing on the Bulldog Powered-Drive Trailer Jack, #BD500200, is 13 inches.

view full answer...

Answer 9

The inner leg of the Bulldog Powered Drive Trailer Jack #BD500200 that you referenced is a solid tube. It does not have a welded seam that runs up the leg of the jack.

view full answer...

Answer 10

For your Bulldog Electric camper jack #BD500200 will run just fine off of any 12V battery. Often the trailers that use these jacks will have other components they will run as well like lighting, vent fans, etc so it is recommended to use a deep cycle…

view full answer...

Answer 11

From the center of the shaft to the front outside edge of the motor housing is 3-1/2 inches. I included some of the mounting plate when I measured for height, which is 8-1/4 inches, since that sticks out over the shaft as well. I also measured from…

view full answer...

Answer 12

The Diameter of the main tube is 2-1/4 inches on the Bulldog Powered-Drive Camper Jack, item #BD500200. There are 6 holes in the mounting plate for either 2-1/2 inch mounting pattern or 3 inch mounting pattern. These are the standard bolt patterns…

view full answer...

Width Of Head On Bulldog Powered Drive Trailer Jack BD500200

Featured Help Information

Miscellaneous Media

Continue Researching