What are the Overall Dimensions of the Dexter Agricultural Hub Assembly # AH15450ECOMP
Updated 04/03/2024 | Published 09/26/2012
Products Featured in This Question
Question:
Do you have overall outer dimensions for this hub? Perhaps simple dimensioned drawing?
asked by: Eric C
Expert Reply:
I pulled the Dexter Hub Assembly, # AH15450ECOMP, from the warehouse and made a simple diagram showing the outer dimensions for you to check out, see photo. This hub comes with the bearings, seal, grease cap and lug bolts.
This hub fits spindle # TRU54FR. If you are not sure what spindle you have or if this hub will fit on your spindle, then you can compare the part numbers of your current bearings to those with this hub assembly or you can take a few measurements of your spindle. The part numbers of your bearings will be stamped into the bearing and in the rubber of the grease seal. If you are unable to locate the part numbers or you no longer have the old bearings, then you can take a few measurements of your spindle to determine what bearings you have. I have also attached a photo showing where to locate the bearing and seal part numbers as well as where to measure on your spindle.
This hub has a 1,500 lb weight capacity and is designed to be used with a 3,000 lb axle. Keep in mind that this is an agricultural hub and is designed to be used with low speed applications such as farm equipment or machinery.
Product Page this Question was Asked From
Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Trailer Hubs and Drums
- Idler Hub
- Agricultural
- LM67048 / LM11949
- Standard Grade
- For 3000 lbs Axles
- 1/2 Inch Stud
- 4 on 5 Inch
- TruRyde
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: as1500e
- Shop: Agricultural Spindle for 3,000-lb Trailer Axles - 1-5/8" Diameter
- Video: Agricultural Spindle for 3,000-lb Trailer Axles Spec Review
- Search Results: lm67010
- Search Results: lm11910
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 2" Diameter
- Shop: Grease Seal - Single Lip - I.D. 1.500" / O.D. 2.332" for Ag Spindle AS1500E - Qty 1
- Shop: Agricultural Spindle for 6,000-lb Trailer Axles - 2-3/4" Diameter
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Shop: #84 Spindle for 3,500-lb Trailer Axles - 1-3/4" Diameter
- Shop: Agricultural Spindle for 3,000-lb Trailer Axles - 1-3/4" Diameter
- Search Results: hub
- Search Results: axle hub
- Shop: Trailer Hub Assembly - 3,000 lbs Axles - 4 on 5 - Agricultural
- Q&A: Hub Recommendation for Spindle with Diameters of .75 and 1.25 inches
- Video: Review of etrailer Replacement Return Spring etrailer Ram Square Direct Weld Jack - TJD-12000-RSP
- Search Results: trailer spindles
- Q&A: Instructions for Disassembling a 12,000 lb Bulldog Jack
- Q&A: Diagram of a 10k Bulldog Landing Gear Jack for Gear Replacement
- Search Results: ramp latch
- Q&A: What Is The Correct Oil To Use In My Dexter Axles With Oil Lube Bath Hubs?
- Q&A: Replacement Grease Seal For a Trailer Hub Using LM11949 Outer Bearing and LM67048 Inner Bearing
- Q&A: Is There a Trailer Hub Assembly with 3/4" and 1-1/4" Bearings
- Article: Parts Needed to Add Hydraulic Disc Brakes to a Trailer
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Article: Trailer Lighting Requirements
- Article: Trailer Wiring Diagrams
- Article: How to Measure Your Trailer Wheel Bolt Pattern
Greg
4/3/2024
John I need to build some yard trailers to move engine blocks around. I have some Titan #16858 hubs that I want to use so my question is will they work on this spindle? The bearing dimensions all match the hubs, but I need to verify the O/S to O/S dimensions between "C" & "D" and between "B" & "D". Is there anyway you find those numbers for me? Thank you for your help.