What Is The Correct Oil To Use In My Dexter Axles With Oil Lube Bath Hubs?
Updated 06/17/2021 | Published 06/16/2021
Question:
What is the right lube weight for dexter axle hubs ? 80w 90 was used to replace the lube that leaked from the broken cap.
asked by: Gerry
Expert Reply:
Dexter recommends a SAE 90, SAE 80W-90 or SAE 75W-90 oil to be used.
I recommend the Kodiak Synthetic Bearing Oil for Oil Bath Hubs # XLPROLUBE as it is a synthetic 90 weight oil that helps reduce friction and to keep bearings cool.
Since your cap was damaged and oil leaked out some dirt may have gotten into the hub. I recommend pulling the hub and cleaning up the bearings and surfaces to reduce the chance of damaging the hub. This will give you a chance to inspect the bearings as well to determine if they need replaced.
If you can send me a picture of the axle information tag or serial number I can get you the numbers for the replacement oil seal and all bearings and races inside your hub.
Product Page this Question was Asked From
Kodiak Synthetic Bearing Oil for Oil Bath Hubs - 8 oz Bottle
- Lubricants Sealants Adhesives
- Oil
- Bearing Oil
- 8 oz
- Kodiak
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Kodiak Synthetic Bearing Oil for Oil Bath Hubs - 8 oz Bottle
- Search Results: dexter oil bath
- Shop: Trailer Hub and Drum Assembly - 7,000-lb Axles - 12" Diameter - 8 on 6-1/2 - Pre-Greased
- Search Results: bearing packer lubricants sealants adhesives
- Search Results: demco ez latch
- Shop: Trailer Hitch
- Shop: Valcrum Universal Threaded Aluminum Oil Bath or Grease Cap for Dexter 9K to 10K GD Axles - Black
- Search Results: dexter 21~36
- Search Results: 10~051
- Search Results: rv corner trim
- Search Results: dexter axle parts
- Shop: Valcrum Universal Threaded Aluminum Oil Bath or Grease Cap for 10K to 16K Axles - Gray
- Shop: Gooseneck Hitch
- Shop: Valcrum Hydro-Shield Waterproof Aluminum Oil Bath or Grease Cap for 9K to 10K GD Axles
- Shop: Replacement Lens, Gaskets, Lens Retainer, Vent Plug, and Screws for Valcrum Universal Oil Hub Caps
- Shop: Replacement Oil Cap Kit for 9,000-lb to 15,000-lb Dexter Axle
- Q&A: What Is the Proper Oil for Oil Bath Hubs on Trailer Axles?
- Video: Detailed Breakdown of the 50MM Nev-R-Lube Bearing for 8,000-lb Dexters
- Video: Review of Valcrum Trailer Bearings Races Seals Caps - Replacement Parts Kit - VA85JR
- Video: Bearing, 42MM Nev-R-Lube 42MM x 76MM x 39MM Feature Review
- Q&A: Nev-R-Lube Trailer Bearings Cannot be Replaced with Regular Bearings
- Shop: Trailer Wiring
- Video: Review of Stillwell Trailer Jack - Jack Direct Weld 10K Conversion Kit - ST24VR
- Q&A: Should There Be A Gap Between The Seal and The Inner Bearing In My Hub
- Q&A: How to Determine What the Correct Replacement Hub Is
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Bearings - DX98ER
- Video: Review of Zerostart Oil Pan Heater - Clamp On Oil Pan And Transmission Heater - ZE23MR
- Video: Valcrum Universal Oil Hub Caps Redress Kit Manufacturer Breakdown
- Q&A: Trouble Removing Spindle Nut On Dexter 10K Axle
- Q&A: Replacement Door Latch Locks For A 2017 Jayco Eagle 5th Wheel With Bauer Door Latch Locks
on Lubricants Sealants Adhesives
