Can You Adjust the Dual Latch Kit Spring for TruXedo TruXport Tonneau Cover?

Question

Question:

The pins came out of the track and I cant get the spring to loosen up how do I do that ? THANKS

asked by: DAVE S

0

Expert Reply:

The Replacement Dual Latch Kit for TruXedo TruXport Soft, Roll-Up Tonneau Covers - Post April 2011 # TX1117755 does not have any way to adjust the spring. You can't tighten or loosen the spring.

expert reply by: Jason S

0

Answer 1

We do have the Replacement Dual Latch Kit #TX1117755 which will fit the TruXedo TruXport Soft, Roll-Up Tonneau Cover #TX271101 if manufactured after April 2011. The date code is printed on the underside of the fabric near the front of the drivers…

view full answer...

Answer 2

To install replacement latches #TX1117755 you will need to remove the tailgate header rail from the side rails. Then you would remove the one fastener per latch holding the old ones on. Next slide off the old latches, slide the new ones into place,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Can You Adjust the Dual Latch Kit Spring for TruXedo TruXport Tonneau Cover?

Product Page this Question was Asked From

Continue Researching