Matching Right Hand (Passenger Side) Trailer Tail Light for Optronics STST26RPG

Question

Question:

The ST27RPG is listed for the left drivers side of the trailer. What is the number for the light for the right passenger side?

asked by: TOMMY P

0

Expert Reply:

The Optronics Over 80", Rectangular Submersible Trailer Tail Light, 2 Wire, 7-Function, Right Hand, part numner # ST26RPG is the part you're looking for.

This is the matching right hand tail light to go with part # ST27RPG (left hand).

expert reply by: Carla M

0

Answer 1

The Optronics LED Combination Trailer Tail Lights #TLL160RK will replace your tail lights for LED on your Heritage trailer. If you are able to remove the clearance lights from their bases we have the following Amber/Red lights below. Thinline LED…

view full answer...

Answer 2

I would go with LEDs but you would have to replace all the lights on the trailer (or at least all the lights on the same circuit would have to be either LED or incandescent). The reason is that LEDs use much less amperage at the same voltage then do…

view full answer...

Answer 3

Hi Eric, We unfortunately do not offer a light with this sizing so alterations would have to be made to the cutout hole in order to get these replaced. If you want to pull the lights out and see if there's any labels with a brand and part number…

view full answer...

Answer 4

We do carry rectangular trailer lights that come with the Plug-N-Go connector like the Optronics Right Hand Trailer Light, #ST26RPG, and #ST36RPG. These two lights come with the 2-wire molded connector. If the connector on your trailer has a 3-wire…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Matching Right Hand (Passenger Side) Trailer Tail Light for Optronics STST26RPG

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching