Is it Okay for the Bumper to Touch the Curt Hitch part # C13043
Updated 07/06/2020 | Published 06/26/2020 >
Question:
i have the same common problem that the curt hitch doesnt clear the bumper lip on the bottom section of my 2015 lexus gx I think adding a couple of washer between the hitch receiver and the frame will solve the issue. Is this is a safety concern since the hitch will not sit flush with the frame after ing a couple of washers? do i need to purchase a longer bolt? I am very confused.
asked by: Chris M
Expert Reply:
You should only use the provided hardware to secure your hitch. Using any additional spacers or washers will void the warranty from the manufacturer.
If it is an issue where the bumper cover is resting on the hitch and you are able to install it and properly torque the hardware this is not an issue and is very common on a lot of the hitches that I have installed. This eliminates the need for you to cut the bumper for clearance since it isn't really an issue.
If you do not like it you can certainly cut the bumper around the area in which it makes contact with the hitch so it is not an issue. This will not negatively effect the hitch's performance.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 500 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- No Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Video: Install: Curt Trailer Hitch Receiver on a 2018 Lexus GX 460
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Q&A: Which Trailer Hitch Receiver for a 2014 Lexus GX 460 is Least Visible
- Video: Mount: etrailer Trailer Hitch Receiver on a 2018 Lexus GX 460
- Q&A: Recommended Trailer Hitch Receiver and Wiring For a 2023 Lexus GX 460
- Q&A: Recommended Trailer Hitch For A 2022 Lexus GX 460
- Shop: Trailer Wiring
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer jack
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Suspension Enhancement
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Video: Installing the Curt Trailer Hitch Receiver on a 2025 Toyota RAV4
- Search Results: trailer tires and wheels
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers


Chris
6/30/2020
I went for it and just screwed it in and it was fine. pretty tight but not too bad. I was concerned for no reason thanks.