Replacement Hitch Pin for Swagman S64400 Original Bike Rack

Question

Question:

I have etrailer tow hitch e98857 and a Swagman 4 bike rack S64400. Is there a replacement hitch pin? Or one that locks? Thank you.

asked by: Bhanu

1

Helpful Expert Reply:

Swagman offers both a non-locking and a locking anti-rattle hitch pin for their # S64400 Original bike rack.

For the non-locking pin, use part # P5901 or part # S64027 for the locking version.

expert reply by: Mike L

1

Answer 1

Each company that uses a threaded hitch pin has a uniquely threaded pin that will only work with the bike racks made by that company. The Swagman Threaded Hitch Pin #P5901 that you referenced is a 5/8 inch pin with coarse threads, but the exact…

view full answer...

Answer 2

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bike racks with 2 inch shanks. This hitch pin actually has an outer diameter of 5/8 inch and is 4-3/4 inches long according to my contact at Swagman so it will not…

view full answer...

Answer 3

You'd need a 19 mm socket or wrench to tighten the bolt of the Locking Anti-Rattle, Threaded Hitch Pin for Swagman Hitch Racks #S64029.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Hitch Pin for Swagman S64400 Original Bike Rack

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching