Replacement Vent Cover for Ventline AS-13M

Question

Question:

Need the replacement cover for Ventline AS-13M the hinge is on one side not in middle.

asked by: Kimberly D

0

Expert Reply:

The correct replacement cover for your Ventline AS-13-M-V101. The replacement cover you want is # BV0554-01 in white or # BV0554-03 in smoke. I've attached video reviews of each of these as well as an installation video to assist.

expert reply by: Jameson C

0

Answer 1

The Dometic CDMW12S requires a 20.39" wide x 14.52" tall x 16.02" deep opening in order to fit so the closest option we currently offer is going to be the High Pointe Standard RV Microwave #HP59ZR (19.1” wide x 11.5” tall x 14.8”…

view full answer...

Answer 2

I contacted Trimark in regards to a replacement part for the Trimark 030-0900. 030-0900 is actually a series number not a specific part number. To find the part number you will need to take the interior handle completely off the unit. On the back…

view full answer...

Answer 3

We do offer replacement lids for the Northern Breeze/Ventline AS-13M. You'd want to go with #BV0554-01 for white or #BV0554-03 for smoke.

view full answer...

Answer 4

The correct replacement cover for your Ventline Northern Breeze VB0568 Roof Vent is the Vent Cover for Ventline Old Style Rounded Dome Trailer Roof Vents #BV0554-01 for white, or #BV0554-03 for smoke. I have attached a couple of videos for you to…

view full answer...

Answer 5

For your Ventline AS-13M you'll want the MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent - Translucent Smoke #MA00-335002 or #MA00-335001 for white. These lids have universal-fit hinges so there's no guessing game about…

view full answer...

Answer 6

We have had a similar question to this come up and we were able to determine that the number AS-13 M-VDO449 that you listed is stamped on the vent cover part #BVD0449-A01. If you are looking for the entire fan setup and not just the cover you would…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Replacement Vent Cover for Ventline AS-13M

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching