Replacement Hardware for Curt Trailer Hitch Receiver 13269

Question

Question:

I am looking for a hardware kit for a Curt trailer hitch for a 2018 Jeep Renegade 4x4. Curt part number 13269-BK.

asked by: Duane

1

Helpful Expert Reply:

For your Curt Trailer Hitch Receiver # C13269 on your Jeep Renegade, you can get the replacement hardware using part # RHK. You just select Curt and then enter the model number and you will get the exact parts kit for your hitch.

expert reply by: Jason S

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 4

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 5

The best hitch for your 2015 Jeep Renegade Latitude that will provide you with the most ground clearance is the EcoHitch Hidden Trailer Hitch Receiver #EH83VR. This hitch is made in the USA, has a bolt-on, no-drill installation and will provide you…

view full answer...

Answer 6

Hi Christina, I wasn't able to figure out what axle you have based on the serial number, but since the label shows the axle was made in 2020, I searched for a 2020 Escape 17B and it should be a Dexter Torflex #10 Torsion axle. The Torflex axle is…

view full answer...

Answer 7

As you can see in the provided photo, the hitch sits far enough below the bumper that no trimming is required. If you'll be using the hitch for towing a trailer, you'll need a few other parts. For a trailer wiring harness, use part #118651.…

view full answer...

Answer 8

For your 2020 Jeep Renegade Latitude the Draw Tite part #76021 is the way to go as it has the highest towing capacities and the easiest install. I attached an install video for this for you to check out as well. Then if you needed trailer wiring as…

view full answer...

Answer 9

Yes, there is a hitch available for your 2023 Jeep Compass. I recommend the etrailer Hitch item #e48AR. This hitch is custom fit and bolts to your Jeep with included hardware. I really like this hitch because the crosstube is hidden behind the rear…

view full answer...

Answer 10

The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e37AR is a confirmed fit for all models of the 2018 Jeep Renegade, so it'll work perfectly on your Renegade Altitude. If you'll be towing with the…

view full answer...

Answer 11

The hitch and wiring I recommend for your 2008 Jeep Wrangler X are the etrailer Trailer Hitch #e98856 and the Tekonsha T-One Wiring Kit #118416. This trailer hitch has a matte black finish that looks more rugged and protects the hitch better than the…

view full answer...

Replacement Hardware for Curt Trailer Hitch Receiver 13269

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching