Can a Jack Hole be Added to an A Frame Coupler

Question

Question:

Do they make one with a trailer jack hole or can we drill a whole in it to fit a trailer jack?

asked by: Steve

0

Expert Reply:

The Demco 50-Degree A-Frame Coupler without Jack Hole part # DM15349-52 is not available with a jack hole. If you want to add your own hole to accommodate a jack that would be acceptable.

expert reply by: Randy B

0

Answer 1

I attached a picture that has the dimension of the #BDSPBQ50 that you referenced. I wasn't sure what other plate you were referring to so I grabbed dimensions for the #BD003135 and the #DL22763.

view full answer...

Answer 2

The Demco 6-Hole Adjustable Channel Bracket - Weld On - 12" Tall - 21,000 lbs #DM66134 is the weld on option for your trailer. There isn't a complete kit we offer, but it sounds like you are seeking the Demco 50-Degree A-Frame Coupler…

view full answer...

Answer 3

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 4

Although it's intended to be bolted in place, the Demco #DM15349-52 coupler mount could certainly be welded instead. I've linked you to a product description video featuing the #DM15349-52 A-Frame coupler mount.

view full answer...

Answer 5

Silver is just the color that Demco likes for their couplers which is why the Demco 50-Degree A-Frame Coupler #DM15349-52 is that color. The two most popular colors are black and silver like this. Demco does offer a red primer version of some…

view full answer...

Answer 6

Hey Drew! If you're wondering how far the #LR76VR will stick off the front of the trailer when installed that would be 2". I went ahead and attached a diagram below with some general measurements for your reference. If you're looking for…

view full answer...

Answer 7

The Demco #DM15349-52 does not include mounting hardware. Demco recommends using grade 5 bolts, and the holes in the coupler are 5/8 inches in diameter. If you click the provided link, you can see a product demonstration video featuring the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Can a Jack Hole be Added to an A Frame Coupler

Product Page this Question was Asked From

Continue Researching