Can DM15349-52 Demco Coupler Mount Be Welded in Place

Question

Question:

Can this coupler be welded on?

asked by: Kody K

0

Expert Reply:

Although it's intended to be bolted in place, the Demco # DM15349-52 coupler mount could certainly be welded instead. I've linked you to a product description video featuing the # DM15349-52 A-Frame coupler mount.

expert reply by: Mike L

0

Answer 1

I reached out to Lets Go Aero for confirmation that you can even use the Demco 50-Degree A-Frame Coupler #DM15349-52 and they said that you will not have any structural issues with having the bolt holes drilled in the sides of your Frame as the Demco…

view full answer...

Answer 2

Silver is just the color that Demco likes for their couplers which is why the Demco 50-Degree A-Frame Coupler #DM15349-52 is that color. The two most popular colors are black and silver like this. Demco does offer a red primer version of some…

view full answer...

Answer 3

I am not aware of a bolt-on version of the Buyers Products Weld-On Safety Chain Retainer part #3375471000. However, if all you were wanting to do is mount your safety chains to the tongue of your trailer then you will just simply do so by running a…

view full answer...

Answer 4

I have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis. However you can simply take a safety chain set like the 42" Long Safety Chain with 3/8" Clevis Hook (15,000 lbs) #337BSC3842 and use a grade 8 bolt…

view full answer...

Answer 5

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 6

I attached a picture that has the dimension of the #BDSPBQ50 that you referenced. I wasn't sure what other plate you were referring to so I grabbed dimensions for the #BD003135 and the #DL22763.

view full answer...

Answer 7

Hey Drew! If you're wondering how far the #LR76VR will stick off the front of the trailer when installed that would be 2". I went ahead and attached a diagram below with some general measurements for your reference. If you're looking for…

view full answer...

Answer 8

The Demco 6-Hole Adjustable Channel Bracket - Weld On - 12" Tall - 21,000 lbs #DM66134 is the weld on option for your trailer. There isn't a complete kit we offer, but it sounds like you are seeking the Demco 50-Degree A-Frame Coupler…

view full answer...

Answer 9

The Demco 50-Degree A-Frame Coupler without Jack Hole part #DM15349-52 is not available with a jack hole. If you want to add your own hole to accommodate a jack that would be acceptable.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Can DM15349-52 Demco Coupler Mount Be Welded in Place

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching