Correct Curt T-Connector Vehicle Wiring Harness for a 2019 Ford Escape

Question

Question:

Installed product number 56320 into my 2019 ford escape. The only thing that was done differently from the instruction manual was the power wire is installed into our rear fuse pannel. When I plug in any trailer the left turn signal will flash both lights on the trailer and the right turn signal will flash no lights on the trailer. What are your thoughts on the problem?

asked by: Tyler

0

Expert Reply:

The correct Curt T-Connector Vehicle Wiring Harness for a 2019 Ford Escape is part # C95FR, not part # C56320 which is a fit for a 2017 - 2018 Ford Escape.

expert reply by: Conner L

0

Answer 1

You are correct the Curt trailer wiring harness part #C95FR is the trailer wiring kit that fits your 2019 Ford Escape SE FWD.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

The Draw-Tite Max-E-Loader Trailer Hitch Receiver part #75758 is the easiest to install trailer hitch for a 2019 Ford Escape and has a class III rating with 2" opening. It does not require that you lower the exhaust or remove any panels. There…

view full answer...

Correct Curt T-Connector Vehicle Wiring Harness for a 2019 Ford Escape

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching