Trailer Hitch Receiver Fit for 2018 Cadillac XT5

Question

Question:

I have a 2013 cadillac srx with your hitch. will that hitch fit a 2018 Cadillac XT5?

asked by: Johnny S

0

Expert Reply:

A trailer hitch from a 2013 Cadillac SRX will not fit your 2018 Cadillac XT5, which means you will need a new hitch.

The hitch I recommend for your 2018 Cadillac XT5 is the etrailer Trailer Hitch Receiver # e62AR.

I like this hitch above the Curt Trailer Hitch # C13285 because the Draw-Tite has slightly better ground clearance than the Curt, which is important to keep things like accessories from hitting the ground. I have added a photo showing with this hitch looks like on a 2018 XT5 as well as a link to a video install for you to check out. Just keep in mind these hitches do not fit the Platinum model of XT5 (there are no hitches for that model).

Additionally, for trailer wiring on a 2018 Cadillac XT5 you need T-One Vehicle Wiring Harness # 118720 for a 4-flat or T-One Vehicle Wiring Harness # 118276 for a 7-way.

expert reply by: Kyle S

0

click to enlarge

Answer 1

While we do not currently carry the Pacific Dualies 18090 valve stem extenders that you mentioned, I did some research and found that the manufacturer does state that they don't recommend them for use with rubber valve stems. From what I could…

view full answer...

Answer 2

You can absolutely put the rear panel back on your 2023 Cadillac XT5 after installing the etrailer hitch that fits, which is the following part number: - etrailer Trailer Hitch Receiver #e62AR This will make it so your Cadillac keeps its aesthetic so…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, the Curt Class III Hitch Receiver #C13285 is confirmed to fit your 2017 Cadillac XT5 base model. It will use existing holes in the vehicle's frame for a no-drill installation and features a towing capacity of 5,000 pounds. I have attached an…

view full answer...

Answer 5

There isn't a trick to removing the cap on the tow plug of your 2019 Cadillac XT5 to install the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector #C56325. I have added a link below to an installation…

view full answer...

Answer 6

Hello Andrew. It looks like our installers have not had the privilege of doing an install on a 2025 Chevy Equinox. I see that the wiring harnesses that we do have in stock have the 6 pin connector. It looks like Curt is aware of this issue and is in…

view full answer...

Answer 7

You can get a complete hardwear kit for the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e62AR with the part #RHK. You will enter the part number e62AR in the box and purchase the kit. We will prepar your a…

view full answer...

Answer 8

There is not going to be a 5 flat that has 8 wires; the functions of the 8 wires are likely ground, running light circuit (split into 2 wires at the plug), left turn, right turn, brake lights (possibly split at the plug), and output to reverse…

view full answer...

Answer 9

Hey Patrick, so when we installed the Curt hitch part #C13285 on a similar 2018 Cadillac XT5 we found there was 5-3/4 inches from the center of the hitch pin hole to the outer edge of the rear bumper.

view full answer...

Answer 10

We do have a receiver that is custom fit for your 2018 Cadillac XT5 but the etrailer Trailer Hitch Receiver #e98865 will not. It is only confirmed to fit the 2005 - 2017 Chevrolet Equinox, 2010 - 2017 GMC Terrain, 2006 - 2009 Pontiac Torrent, and…

view full answer...

Answer 11

We do have two confirmed hitch fits for the 2017 Cadillac XT5 that you can see on the linked page. Both of the 2-inch Class III hitches we have for this vehicle, the etrailer #e62AR and the Curt #C13285, offer no-drill installation and include all…

view full answer...

Answer 12

The etrailer hitch #e62AR and the Curt #C13285 that fit the 2023 Cadillac XT5 are both made by same company so they would have exact same clearance dimensions. Everything I am seeing online says the 24' XT5 is a carryover from the 23' model…

view full answer...

Trailer Hitch Receiver Fit for 2018 Cadillac XT5

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching