Replacement Nylon Fasteners for Furrion Stove Hinges

Question

Question:

Di you have the plastic bolts and nuts wothout the hinges. Mine are breaking after 2 years. I dont need the hinges.

asked by: Patrick F

0

Expert Reply:

The Replacement Hinge for Furrion 2-in-1 Range Oven - Qty 1 # LC719851 is the only way to get the replacement hardware you are seeking. They aren't available separately from the manufacturer.

expert reply by: Jason S

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

Hey Fred! You will need to take some measurements to determine if you will have enough clearance with the B&W Gooseneck Pin Box #BW23RV. You can use the following formula: (A + B) - C = Clearance A = Distance from the gooseneck ball center to the…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

To determine if the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert 1621 and 1621HD #MR84VR will fit your trailer you'll need to first determine your trailer's bolt pattern. There will typically be a sticker (pictured…

view full answer...

Answer 12

Thanks for reaching out, Jim! When the Thomas Payne Trifold #LC22PX is folded down into the bed position, the sleeping area measures 70" long by 55" wide. It's a bit shorter than a full sized mattress but a bit wider than one. Are you…

view full answer...

Replacement Nylon Fasteners for Furrion Stove Hinges

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching