Wind Fairing for Malone AirFlow2 Roof Rack With 58 Inch Crossbars

Question

Question:

Hi, I have mounted Malone Airflow 2 Roof Rack with Aero Blades. I have 3 sets of Thule XT Fairings which I also bought to my old suvs at your website. I have original mounting brackets and Thule square bars adapters. Do you have any adapters or brackets which I can use with Thule XT fairing and Malone Aero Blades?

asked by: Daniel

0

Expert Reply:

The clamps for the old Thule XT fairings have been discontinued, and there are no adapters that are designed to work with your Malone AirFlow2 Roof Rack # MPG216 with 58" crossbars, so the best option really is a new wind fairing.

I recommend measuring the distance between the feet of your Malone AirFlow2 roof rack to ensure a fit, and so long as they are 43" or less apart the wind fairing I recommend is the 50" Rhino-Rack Fairing for Roof Racks # RRRF4.

I have added links to a video review of this for you to check out.

expert reply by: Kyle S

0

Answer 1

Hey Frank, The Malone Fairing for Roof Racks #MAL74SR brackets will be compatible with Ford factory crossbars and has a locking knob to adjust the angle of the fairing to fit different crossbar heights so you shouldn't have any issues. Both the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Wind Fairing for Malone AirFlow2 Roof Rack With 58 Inch Crossbars

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching