Replacement Bushings for Dexter E-Z Flex Equalizers

Question

Question:

Hello. I have a 2012 Keystone Cougar bumper pull. It has dexter axles with I think are 6000 lb axles 6 stud hub. It has ez flex by Trailair equilizer. Is there replacement bushings available? They appear to be the same as spring bushings. 9/16 bore x 1 3/4. Thanks

asked by: Roger

0

Expert Reply:

The correct replacement bushing for your Dexter E-Z Flex equalizers is part # D014-077-00. This comes as a quantity of 1 but you can get a 4 pack as part # K71-291-00.

expert reply by: Jon G

0

Answer 1

Hi Mikolaj, We do have the correct replacement for the E-Z Flex equalizer marked 13-144, and what you need is the Replacement Equalizer for E-Z Flex Suspension Kits #013-144-03. It mentions "triple axle" on the product page but the…

view full answer...

Answer 2

The bushings that come with the part #K71-656-00 are 9/16 inner diameter and 11/16 inch outer diameter. The length is 1-3/4 and for replacements it's part #D014-077-00.

view full answer...

Answer 3

A replacement equalizer will be necessary if the rubber core needs to be replaced. If you measure your equalizer you will be able to determine which replacement you need. For example, the #013-144-03 Replacement Equalizer measures 7-3/4" from…

view full answer...

Answer 4

According to the Dexter Axle instructions, the bolts that are used to install the E-Z Flex Equalizer for 1-3/4" Double Eye Springs #013-144-03 should be torqued in the range of 30 - 50 ft-lbs (see attached cutout). Attached is an installation…

view full answer...

Answer 5

Hello Robert from Norway, and greetings from Wentzville Missouri USA! The 2 bolts for the leaf spring should be tightened but there is no specific torque setting. You don't want them too tight because this could cause the suspension to bind. The…

view full answer...

Answer 6

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 7

Hey Charles, Yes, you can replace nylon bushing with bronze bushings/wets bolts, you'll just want to make sure the useable length matches for both the bolt and bushing. The Step Wet Bolt for 1-3/4" Double Eye Springs #34007-187-00 you were…

view full answer...

Answer 8

The best way to secure you Ferrari F430 to a trailer will involve an E-Track system. For this you are going to want a few items. First you will want a set of tracks like the Erickson Horizontal E-Track part #EM19147. You will want four of them, one…

view full answer...

Answer 9

Hi Robert; thanks for providing that information and the picture. The rubber isn't something that can be replaced so you will need to swap out the whole equalizer. The correct part is the Replacement Equalizer for E-Z Flex Suspension Kits…

view full answer...

Answer 10

I wish I had a good answer for you, but since Kodiak was bought out by Dexter it seems they discontinued the 204 caliper in favor of using the 225 calipers. They both worked on 3500lb axles but the 225 was also able to be used on larger axles up to…

view full answer...

Answer 11

The Curt Hitch Ball #C40085 that you referenced is meant to fit a trailer hitch receiver ball mount. Due to its design it is not compatible with a gooseneck hitch. We do have some gooseneck hitch ball options like the Hide-A-Goose Gooseneck Hitch…

view full answer...

Answer 12

The hub you describe is a 3500 lb 10 inch hub/drum with a 6 on 5-1/2 inch bolt pattern which uses an L44649 outer and an L68149 inner wheel bearing and a 58846 grease seal. For a replacement, I'd recommend the #AKHD-655-35-EZ-K hub/drum. The…

view full answer...

Replacement Bushings for Dexter E-Z Flex Equalizers

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching