K71-656-00 E-Z-Flex Bushing Dimensions

Question

Question:

what are the bushing dimensions ?

asked by: Ray H

0

Expert Reply:

The bushings that come with the part # K71-656-00 are 9/16 inner diameter and 11/16 inch outer diameter. The length is 1-3/4 and for replacements it's part # D014-077-00.

expert reply by: Jameson C

0

Answer 1

The correct replacement bushing for your Dexter E-Z Flex equalizers is part #D014-077-00. This comes as a quantity of 1 but you can get a 4 pack as part #K71-291-00.

view full answer...

Answer 2

Hi Mikolaj, We do have the correct replacement for the E-Z Flex equalizer marked 13-144, and what you need is the Replacement Equalizer for E-Z Flex Suspension Kits #013-144-03. It mentions "triple axle" on the product page but the…

view full answer...

Answer 3

A replacement equalizer will be necessary if the rubber core needs to be replaced. If you measure your equalizer you will be able to determine which replacement you need. For example, the #013-144-03 Replacement Equalizer measures 7-3/4" from…

view full answer...

Answer 4

According to the Dexter Axle instructions, the bolts that are used to install the E-Z Flex Equalizer for 1-3/4" Double Eye Springs #013-144-03 should be torqued in the range of 30 - 50 ft-lbs (see attached cutout). Attached is an installation…

view full answer...

Answer 5

Hello Robert from Norway, and greetings from Wentzville Missouri USA! The 2 bolts for the leaf spring should be tightened but there is no specific torque setting. You don't want them too tight because this could cause the suspension to bind. The…

view full answer...

Answer 6

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 7

Hey Charles, Yes, you can replace nylon bushing with bronze bushings/wets bolts, you'll just want to make sure the useable length matches for both the bolt and bushing. The Step Wet Bolt for 1-3/4" Double Eye Springs #34007-187-00 you were…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

K71-656-00 E-Z-Flex Bushing Dimensions

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching