Will the Footplate for 2-1/4 Inch Round Tube A-Frame Jacks Fit a 2 Inch Jack

Question

Question:

Will this fit over a 2inch rv jack ? The bottom is bent so I cant get one inside

asked by: JACK E

0

Expert Reply:

The Footplate for 2-1/4" Round Tube, A-Frame Jacks part # JF-101BK is designed to slide over an inner tube for an a-frame trailer jack with a 2" outer diameter. Therefore, if the outer diameter of the inner tube on your jack is 2" then the above footplate will fit over this or slide over if you will. If your a-frame trailer jack has an outer tube with an outside diameter of 2-1/4" then odds are it has an inner tube with an outer diameter of 2".

expert reply by: Conner L

0

Answer 1

Hey Alex, welcome back! There's a couple of options for spacers depending on how tall of a lift your 2014 Nissan Xterra has. Timbren recommends leaving a 1/2" gap between the item #TJRC01 and where they contact on your Nissan. How big of a…

view full answer...

Answer 2

You can absolutely still use the Timbren Suspension Enhancement System #TJRC01 with your lifted Nissan Xterra however you're going to need to use a spacer #A25723-90AH00 or 1" or #TA25722-90F00 for 1/2". To find out how many spacers…

view full answer...

Answer 3

Once it's disassembled, once you access the rear of the socket you'll see that it's color coded as shown in the provided photo. The corresponding plug, like #A10-30FDT would wire in the same manner. The screws on each terminal are color…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will the Footplate for 2-1/4 Inch Round Tube A-Frame Jacks Fit a 2 Inch Jack

Product Page this Question was Asked From

Continue Researching