Mounting Hole Distance Of Titan 2-Tang Clevis T1807800

Question

Question:

What is the distance between the mounting holes? Looking for something 2inch on center.

asked by: Brandon

0

Expert Reply:

The mounting holes are exactly 2 inches on center apart on the Titan 2-Tang Clevis part # T1807800. I have attached a very helpful video that points out the measurements for you.

expert reply by: Heather A

0

Alan W.

7/14/2020

what size are the mounting boltholes (cross bolts)

Chris R.

7/20/2020

The mounting bolt holes for the Titan 2-Tang Clevis # T1807800 have a 5/8" diameter.

Answer 1

The width of the Titan 2-Tang Clevis #T1807800 is 3 inches as this is designed to fit 3 inch channel like the #BDAC5000300.

view full answer...

Answer 2

That is a pretty good guess! The two position mounting channel in the #T1812200 is 3-1/2" wide x 7-1/2" tall as shown in the included diagram. I included a video review of the #T1812200 for you to take a look at.

view full answer...

Answer 3

The Dexter 2-Tang Clevis #T1807800 has mounting holes that will line up with the BulletProof Hitches 2-Ball Mount for 2-1/2" Hitches #MD254, but the Clevis uses 3/4" pins while the BulletProof shank uses 5/8" pins for the ball mount.…

view full answer...

Answer 4

I went out to our warehouse and pulled a Titan clevis attachment #T0897900 to measure it for you. The overall width at the widest point is 2-13/16 inches. The holes are spaced 2 inches apart on center. I have included a picture showing these…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Mounting Hole Distance Of Titan 2-Tang Clevis T1807800

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching