How to Measure Trailer Brake Drum for Electric Trailer Brake Assemblies

Question

Question:

do u measure the brake drum to deturmen the size brake u need-10

asked by: Robert S

0

Expert Reply:

The inside diameter and the depth of the brake drum is what determines the necessary width of the brake pads. For example, the 10 inch x 2-1/4 inch Electric Brake Shoe, part number BP04-090 that you refer to would fit a brake drum with a 10 inch diameter and 2-1/4 inch depth.

expert reply by: Mike L

0

click to enlarge

Jeffrey M.

6/18/2020

Thank you, your a life saver!

Answer 1

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 2

Hello Ted. The Dexter Electric Trailer Brakes #23-47-48 use 14 gauge wire. We recommend using 10 gauge wire like part #10-1-1 which we sell by the foot. For a butt connector I recommend using part #05732-2. These are made for 10 or 12 gauge wire but…

view full answer...

Answer 3

The wires on the Dexter Nev-R-Adjust Electric Trailer Brake Assembly #K23-478-00 are 12 gauge wires. We recommend using 10 Gauge Wire #10-1-1 from the trailer 7-Way connector to the brakes though to help ensure enough power gets to them.

view full answer...

Answer 4

A trailer that is over 80 inches wide is required by DOT regulations to have rear clearance lights. An over 80 inch taillight kit, like part #TL16RK, will have the side clearance light built into it. An under 80 inch taillight does not have the…

view full answer...

Answer 5

The reason for four wires on your trailer is that one of the wires will normally be spliced toward the rear of the trailer and will run to both sides of the trailer for the running lights. I have attached a photo of a wishbone connector. You can see…

view full answer...

Answer 6

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 7

That would be the depth of the inside of the hub. If you check out the picture I attached the blue lines represent the depth. This will also be the width of the brake shoes on the brake assemblies. I attached a review video for this hub for you to…

view full answer...

Answer 8

To slightly lower your trailer that has had an "axle flip" kit installed you would want to use slightly shorter shackle straps, not longer ones. Shorter shackles will let the axle rest closer to the trailer frame, which lowers the trailer…

view full answer...

Answer 9

Thank you for the info you found on your current hub/drums. Based on that the correct replacement would be the part #8-247-50.

view full answer...

Answer 10

Hey Doug, thanks for the information. I searched that part number and wasn't able to find any information on it. The etrailer Electric Trailer Brakes item #AKEBRK-35-SA do fit a 10" diameter x 2-1/4" wide drum and have a 3,500 lbs…

view full answer...

Answer 11

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity box.…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

How to Measure Trailer Brake Drum for Electric Trailer Brake Assemblies

Continue Researching