Adapter for Larger Rack to use Rhino-Rack Fishing Rod Carrier

Question

Question:

Will it fit my lumber rack?

asked by: Tom

1

Helpful Expert Reply:

So the answer to this really depends on the diameter of the bars on your lumber rack. If they are less than 2 inches then you can use the Rhino-Rack Fishing Rod Carrier - Locking - 8 Fishing Rods # RR574F on your lumber rack. To do so you would need the Heavy-Duty Crossbar Adapter Kit # HD-FK1.

I have added a link to a video review of the carrier for you to check out as well.

expert reply by: Kyle S

1

click to enlarge

Tom

2/17/2020

The lumber rack is exacly 2 inches , you stated they would fit if they were under 2 inches. Will this work or should i look for a different product

Jason S.

2/18/2020

The Heavy-Duty Crossbar Adapter Kit for Rhino-Rack Ski and Snowboard Carrier, Kayak Carrier, or Fairing # HD-FK1 gives you 55mm long hardware which is 2.1653 inches. Since your bars are 2 inches, you may need longer hardware. These bolts are m6 x 55mm so you would simply need longer m6 screws to allow the rod carrier to fit.

Answer 1

Not all trailer axles have the EZ lube zerk fitting so what you have is totally normal. You can use a Bearing Buddy like you mentioned but we have found is that the Bearing Buddies make it too easy to add too much grease which then blows out the…

view full answer...

Answer 2

EZ lube spindles are more than just a zerk fitting attached to the end of the spindle. There would need to be a hole in the spindle between where the bearings ride for the grease would then fill the hub by. To be perfectly honest using EZ lube…

view full answer...

Answer 3

Grease Cap set #RG04-040 are regular grease caps that have a rubber plug on the end to access a grease zerk fitting on the spindle (end of the axle). They install the same as regular grease caps. It sounds like you are looking for bearing protectors…

view full answer...

Answer 4

Yes! Rhino-Rack's Locking Fishing Rod Carrier #RR574F will fit just fine on the elliptical bars of your 2011 Honda Pilot's roof rack thanks to its universal mounting hardware that fits all popular roof rack bar shapes. Once installed the…

view full answer...

Answer 5

Thanks for the photo for clarity. The Rhino-Rack Fishing Rod Carrier - Locking - 8 Fishing Rods #RR574F won't have any issue with the curved crossbars. The 6.5 foot sections of the 13 foot surf rods should work very well for this application.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hey Sean, yes you can use the TowSmart Adjustable Ball Mount #TS89VR in the Gen-Y Voyager Ball Mount #GY52JJ. This will provide cushioning to the adjustable ball mount plus some additional drop. What are you planning on towing with this setup?

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hey Michael, sure can! For a 5' Leer topper, I am thinking the 55" long x 49" wide LockNLoad platform will be the best bet and will fit comfortably on the topper. Here is a list of all the parts you will need for that: - Yakima 54"…

view full answer...

Adapter for Larger Rack to use Rhino-Rack Fishing Rod Carrier

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching