Curt Hitch for 2017 Buick Envision that Allows Reinstall of Lower Rear Bumper Cover

Question

Question:

After instalation of this hitch will the bumper hitch/cover go back in place using the 2 screws removed during he installation of the hitch. I dont mind having to replace the two screws and cover when not using the hitch as we dont want to see the hitch when not in use. Thanks for your informaton,

asked by: Ed Z

0

Expert Reply:

You can reinstall the lower rear bumper cover of your 2017 Buick Envision after the install the Curt trailer hitch part # C13292 you referenced. If you check out the 20 second mark of the install video I attached you can see our installer removing the cover easily to access the hitch as needed.

expert reply by: Jameson C

0

John C.

4/21/2020

My hitch is on the way, but I need a torque wrench. Can you tell me what torque is required on the chassis bolts?

Chris R.

4/23/2020

For the Class III Trailer Hitch # C13292, Curt states to torque all 7/16" hardware to 59 ft-lbs and all M10 hardware to 40 ft-lbs.

G.chadha

1/11/2021

Hi, I'm looking at the hitch #C13405. Is that compatible with a 2018 envision or do I need to stick to #C13292 ? I'm interested in a product where i would not need to take the trim apart but understand if that will be the only option

Jon G.

1/15/2021

The Curt Hitch # C13405 fits a 2019 - Current Buick Envision. Since you have the 2018 you're going to need to stick with the Curt # C13292 mentioned above. The one nice thing about this option is that you can put the trim piece back in place if you want that OEM look. Otherwise there is no rule saying that you need to put that trim piece on anytime you aren't using the receiver - you can very well leave it off full-time if you want.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Curt Hitch for 2017 Buick Envision that Allows Reinstall of Lower Rear Bumper Cover

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching