Center to Center Bolt Hole Distance Where the Tire Mounts on Bumper Mounted Tire Carrier # TR-1

Question

Question:

Hi. What is the distance on center of the bolts that bolt to the actual wheel?

asked by: Bob

0

Expert Reply:

I went out to the warehouse and pulled a bumper mounted tire carrier # TR-1 to measure. The mounting holes where you would mount the tire are 3 inches apart on center. I have included a picture showing this measurement for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

Looking at the BAL Retract-A-Spare it has a much different design than the Lippert Spare Tire Winch #LC159056 you found. You may be able to mount the new winch so it will still work on your trailer but as we do not have both the products here with…

view full answer...

Answer 2

If you check out the diagram I attached of the side of the Lippert Components Spare Tire Winch #LC159056 that mounts you can see that the distance between the mounting hole locations is 5-1/4" on center. I reached out to my contact at Lippert…

view full answer...

Answer 3

It's possible the Lippert Spare Tire Winch with Offset Cable #LC159056 could attach to the studs you have under your RV frame but the studs would need to be 5-1/4 inch apart on center as this has mounting holes that are 5-1/4 inches apart. The…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Center to Center Bolt Hole Distance Where the Tire Mounts on Bumper Mounted Tire Carrier # TR-1

Product Page this Question was Asked From

Continue Researching