Replacement Rear Latch Clamp for Extang Solid Fold

Question

Question:

Where can I get the hold down latch for Extang solid fold?

asked by: Louis S

0

Expert Reply:

Thanks for the picture of the latch you are needing. Based on that you are in need of the part # EX1035 which is a replacement tail clamp assembly for the Solid Fold.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I didn't receive a picture but I do have a couple of options for clamps that are similar to the one you referenced. They both also include bolts so hopefully one of them is what you are looking for. The Replacement Tail Clamp Assembly for Extang…

view full answer...

Answer 2

The new and improved tail gate clamps are in fact informally also refereed to as EZ-Lock Clamps. While the first generation Extang Solid Fold line along with most of its replacement parts have been discontinued, there are a few parts, like the…

view full answer...

Answer 3

How to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers #EX1035 depends on what cover you have. The replacement tail clamp fits the Extang Solid Fold, Solid Fold 2.0, and Trifecta covers. The Solid Fold…

view full answer...

Answer 4

I have attached a page from the installation instructions for the Extang Solid Fold 2.0 Hard Tonneau Cover #EX83475-62. The page shows the parts that should be used with the rear panel you said blew off. You can look at the page to make sure all of…

view full answer...

Answer 5

The Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers #EX1035 and front clamp #EX42FJ have a very basic design of a bolt with a nut on the end. You will remove the hinge cap or latch pocket cover from the cover and simply slide out…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Rear Latch Clamp for Extang Solid Fold

Product Page this Question was Asked From

Continue Researching