Which Front Hitch for 2020 Ford F-250 Sticks Out the Least

Question

Question:

Which front hitch should I get for my 2020 Ford F-250? I'd prefer one that doesn't stick out too far.

asked by: Dale

0

Expert Reply:

Of the two hitches that fit your 2020 Ford F-250 the Curt hitch part # C31078 sticks out less than the Draw Tite part # 65078. I attached two pictures to show you the difference. The Curt is the first picture and the Draw Tite is the second.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I attached pictures that show how the Curt front hitch #C31078 and the Draw Tite #65076 looks when installed and you can tell that the Draw Tite sits up a bit higher since it comes through relative to the curve in the air dam.

view full answer...

Answer 2

If you are carrying more than 500 lbs on the front of your F-350 then the only front mount hitch that will work is the EcoHitch item #306-X7904. This hitch has a 1,000 lbs vertical load limit (tongue weight). The Curt item #C31078 only has a 500 lbs…

view full answer...

Answer 3

I have a solution for you, but the Curt #C31008 is only designed to fit on 2008-2010 Ford Super Duty trucks. For a 2019 Ford F-350 you'll need the Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2" #C31078, which is the confirmed…

view full answer...

Answer 4

I like the Draw Tite part #65076 for your 2020 Ford F-350 Super Duty as it has the best ground clearance. The Curt part #C31078 sits a bit lower which I don't think you'll want.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Which Front Hitch for 2020 Ford F-250 Sticks Out the Least

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching