Hydraulic Line Size Used with Demco Reverse Lockout Solenoid DM5837

Question

Question:

Wats the line measurement 3/8 or 5 /16

asked by: Guillermo T

1

Helpful Expert Reply:

The Reverse Lockout Solenoid in the Demco kit # DM5837 installs in line with your master cylinder and a standard 3/8" hydraulic line, like # T0980100.

The # DM5837 is designed to work with Demco models DA10 and DA91 hydraulic trailer brake actuators.

expert reply by: Jesse M

1

Answer 1

Hey Carl. To replace the surge brake actuator on your 2012 Jayco Pop-Up camper, I recommend the Demco Hydraulic Brake Actuator item #DM72VR. This actuator fits a 3" wide channel and bolts directly to it. It has a 7,000 lbs capacity, fits a…

view full answer...

Answer 2

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 3

You will have to go out and measure the rollers you have on your trailer if you are looking for an exact replacement to use. You will want to measure the overall diameter of them plus the diameter of the hole that runs down the middle of them. For…

view full answer...

Answer 4

Hello Bob, For your Demco DA70 actuator use the Reverse Lockout Solenoid #DM11993. The difference between this and #DM5837 is that the latter comes with a cover.

view full answer...

Answer 5

Yep, we do have a reverse lockout solenoid for the Demco Hydraulic Brake Actuator #DM72VR. There isn't a manual lockout option, so if you're okay with that, what you need is the following: - Reverse Lockout Solenoid Kit #DM5836

view full answer...

Answer 6

The installation of the Replacement Solenoid Valve for Titan Brake Actuators #T4748800 to your Demco Hydraulic Trailer Brake Actuator for Drum Brakes #DM72VR is a very simple installation. This reverse lockout solenoid valve is threaded into the rear…

view full answer...

Answer 7

Hello Keith, Yes, the Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs #DM72VR will work great for replacing the TDE-660 Hydraulic Actuator. The bolt holes are even 3" apart, just like the one you are replacing. The only…

view full answer...

Answer 8

Hey Greg, I checked the manual for the Demco DA91 actuators like part #DM8759131 and if the lever is pulled it can be disengaged by using a screwdriver to lift upward on the front of the flat emergency lever spring while pulling lever forward till it…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Hydraulic Line Size Used with Demco Reverse Lockout Solenoid DM5837

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching