Does Curt Trailer Hitch # 13534 Stick Out Beyond the Bumper on a 2012 Toyota Highlander
Updated 04/22/2013 | Published 04/24/2012 >
Question:
Does the receiver stick out beyond the rearmost point of the bumper of the vehicle? I have tight space when I back into my garage, and I do not want this to stick out well beyond the bumper.
asked by: Faisal Z
Expert Reply:
On the Toyota Highlander models on which we have installed Curt trailer hitch # 13534, we have found that from the center of the hitch pin hole back to the rear bumper is approximately 2 inches. This would put the receiver face just about flush with the rear bumper. However, there may be some subtle differences between models, even in the same year that could result in the receiver face being at most only a few inches, so you should not have any issues. I have included a link to a video showing installation and a link to the instructions for you.
If you plan to do some towing I recommend etrailer ball mount kit, # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. For trailer wiring use # 118449. I have included instruction links for the wiring as well.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: 989900
- Search Results: 118449
- Shop: Trailer Wiring
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Video: Trailer Wiring Harness Installation - 2011 Toyota Highlander
- Q&A: Troubleshooting Installation of Tow Ready Wiring Harness on 2016 Toyota Highlander
- Q&A: Installation Details for Curt Trailer Hitch Receiver, Part # 13534, on a 2013 Toyota Highlander
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Suspension Enhancement
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer tires and wheels
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Measure for Trailer Hitch Drop
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch ball mount
- Shop: Brake Controller




Rebecca R.
4/8/2013
Why on my 2013 Highlander does this model stick out a full 2 inches? We had it professionally installed but I was surprised it was not closer to flush. Are there any other hitches that would not stick out as far? If there were, I would consider trying another one, as I find this very annoying and have banged my leg on it twice already.