Replacement Bearing Buddy Bra for Outer Diameter of 2-1/8 inch

Question

Question:

The outside diameter on trailer hub is 2 1/8. What caps do I need for my bearing buddy system?

asked by: Paul B

0

Expert Reply:

Since you said the outer diameter of the Bearing Buddy you have now is 2-1/8 inch the correct replacement bra for it is the part # BB19B.

expert reply by: Jameson C

0

Answer 1

The plastic caps for the Bearing Buddy bearing protectors that you are looking for are the Bearing Buddy Bras. We carry three different bras, #BB17B, #BB19B and #BB23B that fit different ranges of Bearing Buddy sizes. You should choose the Bearing…

view full answer...

Answer 2

The Replacement Bearing Buddy Bras - Model 17B #BB17B have an outer diameter of 2 inches and are direct replacements for models 1781, 1781SS, 1810 and 1810SS Bearing Buddies. I assume this is the diameter of the cap you were referring to, and if so,…

view full answer...

Answer 3

First, make sure that you have the correct size Bearing Buddy. It should be slightly larger than the hub bore though it is difficult to tell just by looking. If you can tell me the outer bearing number I can determine which is the correct model.…

view full answer...

Answer 4

You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as #PTW80157. Calipers are needed because the measurement has to be as accurate…

view full answer...

Answer 5

The Replacement Bearing Buddy Bras Model 17B, part #BB17B, will fit on Bearing Buddy grease caps for hub bores from 1.781-inches to 1.810-inches. These caps will have an outer diameter of close to 2-inches. Because these bras are made of flexible…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Bearing Buddy Bra for Outer Diameter of 2-1/8 inch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching