What Size Tube Will The Lipper Replacement Foot Assembly Work With?
Updated 10/09/2019 | Published 10/07/2019
Products Featured in This Question
Question:
What is the height from the bottom plate to the 7/16 hole. Im looking to attach a square tube, and need the tube to reach an angle of around 45 degrees
asked by: Eric W
Expert Reply:
I spoke with Lippert and they gave me the dimensions from the outside of the 2 mounting flanges on the Replacement Foot Assembly # LC157584 as 2-7/8"; so you'll need to use a 2-3/4" square tube to fit in between them and a 3" bolt.
You could also use the Replacement Front Foot Pad # LC362486 which is for 2" x 2" tubes or the UltraFab # UF17-940006 which has 1-5/16" inner dimensions of the 2 mounting flanges.
Product Page this Question was Asked From
Replacement Foot Assembly for Lippert Components Power Stabilizer Jacks - Qty 1
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Jack Foot
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer jack
- Search Results: snapper pins
- Search Results: landing gear pads
- Search Results: stabilizer jack switch
- Search Results: smart plug
- Video: Lippert Components Trailer Jack LC362486 Review
- Video: Review of RVpaws V2 Replacement RV Foot Pads 2 Inch Square Leveling Jack Leg - RV64FR
- Shop: Lippert Waterproof On/Off Switch Assembly for Electric Tongue Jacks
- Shop: RV Designer Contoured Slide-Out Switch with Bezel - 20 Amp Continuous - Black
- Shop: Replacement Front Foot Pad for Lippert Components Ground Control 3.0 Leveling System
- Shop: etrailer Adapter Brackets for Solera Slide-Out Toppers - Qty 2
- Shop: etrailer RV Slide-Out Topper - 132" Wide - 4-Layer Vinyl - Black
- Search Results: 5th wheel hitch rails
- Search Results: lippert 1116 5th wheel pin box
- Shop: SnapPad Jack Pads for Class A and C Motorhomes w/ 9" Round Jack Feet - Qty 2
- Shop: SnapPad XTRA Square 5Jack Pads for Lippert Leveling Systems - 5-1/2" Square Feet - Qty 4
- Q&A: Is the Smart Plug a Direct Replacement to My Current Plug on My 2025 Flagstaff 25SRK?
- Q&A: Recommended Landing Gear Foot Plate for 9 Inch Round Upgrade on 2016 Flagstaff Super Lite 5th Wheel
- Q&A: Troubleshooting Lippert RV Jack that will Retract but Won't Extend
- Video: Lippert Components Trailer Jack LC387874 Review
- Video: Review of SnapPad Stabilizer Jack Pads - SN94VR
- Video: SnapPad SnapJack QD RV Stabilizer Jack Pads Feature Review
- Video: Let’s Check Out the Replacement Pad for SnapPad Jack Stand Pad System
- Video: Feature Breakdown: SnapPad XTRA Square 5Jack Pads for Lippert Leveling Systems
- Shop: Fifth Wheel Hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Wiring
on Accessories and Parts
Eric
10/7/2019
What is the height from the bottom plate to the 7/16 hole. Im looking to attach a square tube, and need the tube to reach an angle of around 45 degrees