Load Capacity for Rackem Fitz-All Enclosed Trailer Ladder Rack

Question

Question:

load capacity at 7 ft width, per unit. thank you

asked by: Tom

0

Expert Reply:

The weight capacity for Rackem Fitz-All Enclosed Trailer Ladder Rack part # RA-28 at a 7 ft width is 400 pounds. These racks are designed for fiberglass ladders, if you need more
capacity another set can be added to spread the weight out more.

expert reply by: Robert G

0

Answer 1

The Rack'em Fitz-All Enclosed Trailer Ladder Rack #RA-28 that you referenced can indeed be cut down a bit to bring the crossbars closer to the roof of the trailer. When we installed the system we cut down the support by about 5 inches and this is…

view full answer...

Answer 2

Yes, we do have a roof rack that will work with the rounded roof on your Interstate cargo trailer. It is the Rack'Em Fitz-All Enclosed Trailer Ladder Rack item #RA-28. This roof rack has a 400 lbs capacity and mounts to the side of your trailer…

view full answer...

Answer 3

Rain gutters on an enclosed trailer will be located at the tops of the two sides of the trailer very near the roof. The gutters are essentially concave tracks that run from front to back. If you check your trailer roof where it meets the side panels…

view full answer...

Answer 4

Since your trailer has rain gutters the Rack'em Fitz-All Enclosed Trailer Ladder Rack #RA-28 that you referenced will fit and work well as that's what it requires to install. It's normally used on RV's but the Stromberg RV Ladder part…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 12

Hi Michael, I'd be happy to help with that. By the way, I love the Flying Cloud. The etrailer Electric Trailer Jack, Part #e33KV, is exactly what you need for your Airstream Flying Cloud 23FB. It has a 5,000 pound lift capacity, which gives you…

view full answer...

Load Capacity for Rackem Fitz-All Enclosed Trailer Ladder Rack

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching