Which Wire is Positive and Negative of Heng's Roof Vent Motor

Question

Question:

Hengs 12v 1.6amp fan motor has two wires, one black one white. Positive/Negative??

asked by: Phil S

1

Helpful Expert Reply:

For the fan motor you mentioned having black would be power and white would be ground. Also, since this is a DC motor if you reverse the wiring it will just reverse the direction of the fan.

expert reply by: Jameson C

1

Answer 1

That is a good question, and you can leave your current fold-out steps up and in the folded position when installing the mounting bracket of the Brophy Scissor Steps. The reason is, the bracket will be installed just underneath the door so as long as…

view full answer...

Answer 2

Thank you for the image Mike. You are most likely going to need the 5 Step Hand Rail #AHR5 but I do recommend measuring to see where the handrail is going to end up. First of all the post for the handrail places the bottom of the rail 43" from…

view full answer...

Answer 3

Yes, the turnbuckle part #TB38 is one of the turnbuckles that comes with the kit part #TDHP which has a 3,000 lb capacity as a set. The 3,000 lbs would be a safe working load limit and not the break strength capacity which Brophy does not list.

view full answer...

Answer 4

The Brophy Basic Turnbuckles w/ Hardware for Camper Tie-Downs item #TDHP are going to be the shortest option we carry. With the hooks on the turnbuckle portion out from the inside of one hook to the inside of the other hook is 12". The minimum…

view full answer...

Answer 5

Typically trailer campers will have 7-way connectors that you'd run to 7-way socket in the bed of the truck which you could install in your Silverado truck bed part #41157. This will cover the clearance light circuit and have the 12 volt power…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Which Wire is Positive and Negative of Heng's Roof Vent Motor

Continue Researching