Coil Resistance of Dexter Axle 7" Brake Assembly Kit

Question

Question:

What is the coil resistance of the magnet coil for a Part Number 23-47-48 7inch brake assembly? I have them on order and want to make sure of the wire size needed to carry the current needed by the each of the two magnet coils that I will be using. Thanks

asked by: Bruce B

0

Expert Reply:

I reached out to my contact at Dexter Axle and she said that the Dexter Electric Trailer Brake Kit # 23-47-48 have a coil resistance of 3.9 ohms per magnet. When it comes to wire size we recommend at least 10 gauge wire like part # 10-1-1 (sold by the foot) for brake assemblies.

expert reply by: Jon G

0

Answer 1

Assuming that when you tested the resistance of the brakes you were testing the two wires on each magnet and getting 2.0 and 2.8 ohms the magnets on your trailer are not working correctly and will need to be replaced. For 7" brakes you should…

view full answer...

Answer 2

The replacement dust cap for the trailer hub you mentioned part #8-393-6UC3-A is the part #38605

view full answer...

Answer 3

We do recommend switching over to an 8 on 6-1/2" bolt pattern when adding disc brakes to a 7K axle. All of the 6 lug disc brake kits are going to be rated for 6K and under. For a full disc brake conversion I recommend the Hydrastar Conversion…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Coil Resistance of Dexter Axle 7" Brake Assembly Kit

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching