Grease / Oil Seals 10-10 Double Lip Seals RG06-090 are the Same as National 470972

Question

Question:

is this the same as national 470972

asked by: Dan G

0

Expert Reply:

Yes, the RG06-090 replaces the National 470972. On the product page we have a link to the cross-reference for the National part number.

expert reply by: Robert G

0

Answer 1

I have attached a photo of the inside of a hub you can check out. In the photo the arrow indicates how the seal is installed on the hub. As you can see the flat side of the seal is flush with the edge on the inside of the hub.

view full answer...

Answer 2

The grease seals in Kit #BK3-100 are not the same as 21333TB. The correct replacement seal for that would be #RG06-090, which have a 2.125" inner diameter and 3.376" outer diameter.

view full answer...

Answer 3

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Answer 4

Some trailers are equipped with EZ Lube spindles, which have a grease fitting or zerk in the end of the spindle, and a small hole in the spindle that lets grease enter the interior of the hub and reach the bearings. This allows grease to be added to…

view full answer...

Answer 5

From what I was able to determine, your CR 21352 grease seal is a Chicago Rawhide 21352 and should be a double lipped seal with a 2.125" ID and 3.376" OD. To replace a seal of that size you'll want to use the #GS-2125DL, which has the…

view full answer...

Answer 6

Hey Mark, thanks for the pictures. That is a pretty interesting trailer. I can't say I have seen anything like that before on a trailer with a single leaf spring spanning the whole axle like that. It almost looks homemade or like someone used an…

view full answer...

Answer 7

I wasn't able to find anything in regard to a replacement part for your TDE 11029C hub assembly, but if you can pull your hub and either look for bearing/grease seal parts numbers or measure the different locations on your spindle then I can see…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Grease / Oil Seals 10-10 Double Lip Seals RG06-090 are the Same as National 470972

Product Page this Question was Asked From

Continue Researching