Is Weight Capacity of Rhino-Rack Roof Rack System Y01-130B Static or Dynamic

Question

Question:

I see that it can support up to 220 lbs but is that static or dynamic weight limit?

asked by: Eddie A

0

Expert Reply:

The 220 lb weight capacity of the Rhino-Rack Roof Rack System # Y01-130B that you referenced is a dynamic weight capacity. This means it's the weight it can carry when on the road. Static would be capacity standing still which Rhino Rack does not offer that figure.

expert reply by: Jameson C

0

Answer 1

I cannot speak for all roof top tents but if you are referring to the Yakima SkyRise Tent for Roof Rack Crossbars part Y07436 then yes, it will work with the Rhino-Rack Roof Rack System part #Y02-490B. So long as you do not exceed the 400 lb weight…

view full answer...

Answer 2

Where you install the tracks on your Rhino Rack Heavy-Duty Bar Roof Rack #Y01-130B depends on the width of the bars that you're using in most cases, but you'll also want to make sure that the tracks are able to sit flat on the topper. The…

view full answer...

Answer 3

We can get you the parts needed to install a roof rack on your truck topper so you can haul your canoe. There are advantages to systems in regards to quality and value, and for your application the best fit is from Rhino-Rack, who is known for their…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is Weight Capacity of Rhino-Rack Roof Rack System Y01-130B Static or Dynamic

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching