Replacement Brake Calipers and Mounting Brackets for Load Rite Tandem Axle Trailer with 3.5K Alxes
Question:
I have a Load Rite boat trailer Tandem 3500# with a Tie Down system. Are the Tie Down caliper mounting flanges compatible with the 3500# kodiak calipers? If they are not compatible, can I just get the caliper and new flanges? Im looking to just replace the calipers rather than do a rebuild given the age of the trailer.
asked by: Omar B
Expert Reply:
Because Kodiak hasn't tested their calipers with brackets from Tie Down, they weren't able to say if they'd be compatible. We do offer the calipers and the brackets sold separately, though.
The caliper is part # KDBC225KG and the bracket needed will depend on what type of rotor you have. If you have a hub/rotor, use # KCMB10HRD or # KCMB10RD if you're using a rotor that slips over an idler hub. Each part is sold individually.
Products Referenced in This Question
Replacement Mounting Bracket for Kodiak Disc Brake Caliper - Integrated Rotor - Dacromet - 3,500
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- 3500 lbs
- Caliper Parts
- Hardware
- Mounting Brackets
- Kodiak
more information >
Replacement Mounting Bracket for Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- 3500 lbs
- Caliper Parts
- Hardware
- Mounting Brackets
- Kodiak
more information >
Kodiak Disc Brake Caliper - KodaGuard - 3,500 lbs to 6,000 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- 3500 lbs
- 6000 lbs
- Caliper Parts
- Caliper
- Kodiak
more information >
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Continue Researching
- Shop: RV Bearing
- Shop: Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet and KodaGuard - 3,500 lbs
- Shop: DeeMaxx 10" Hub/Rotor Assembly - 5 on 4-1/2 - Maxx Coating - 3,500 lbs
- Q&A: What Disc Brakes Do You Recommend For 2003 521 Ranger With A Tandem Axle
- Search Results: 10 19 seal
- Search Results: l68111
- Q&A: Replacement Disc Brake Kit For Homemade Boat Trailer and TDE 46245 Rotors
- Q&A: Is the Kodiak Disc Brake Kit # K2HR35DKG a Grease or Oil-Bath Setup
- Q&A: Will Kodiak Disc Brake Kit part # K2HR35DKG Fit 13 inch Trailer Wheels
- Q&A: Is the Aluminum Hi-Spec Series 06 Trailer Wheel AM22328BP Compatible with ST215/75R14 Tires
- Search Results: 10~19
- Q&A: Recommended Replacement For A Tie-Down Engineering Disc Brake Hub
- Q&A: Would the Aluminum Sendel Series T07 Trailer Wheel AM25DR Replace 14x6 Rim
- Search Results: l44610
- Search Results: l44649
- Search Results: l68149
- Search Results: kodiak disc brake kit
- Video: The Low-Down on the Kodiak Disc Brake Kit-K2HR35DKG
- Shop: Replacement Race for L68149 Bearing
- Shop: Aluminum Hi-Spec Series 06 Trailer Wheel - 14" x 5-1/2" Rim - 5 on 4-1/2 - Silver
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Dacromet and Stainless Steel - 3,500 lbs
- Shop: Replacement Race for L44643 and L44649 Bearings
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Video: Replacement Mounting Bracket for Kodiak Disc Brake Caliper Spec Review
- Article: How to Bleed Your Trailer Surge Brakes
- Video: All You Need to Know About the DeeMaxx 10" Hub/Rotor Assembly
- Video: The Low-Down on the DeeMaxx Ceramic Brake Pads with Steel Back Plates- 3,500 lbs to 6,000 lbs
- Video: Replacement Mounting Bracket for Kodiak Disc Brake Caliper Review
- Video: A Closer Look at the Mounting Nut for 7" and 10" Brake Assemblies
- Video: Comprehensive Review: AirBedz XUV Air Mattress w/ Built-In Battery-Powered Pump